Matrix SPARSH VP710 User Manual Download Page 78

Page: 78 / 1046

Matrix SPARSH VP710 User Guide

•

Tap

to accept the change or

to cancel.

You can configure a static IPv4 address for the IP phone. Before configuring it, make sure that the

mode

is configured as

IPv4

IPv4 & IPv6

To configure a static IPv4 address via phone user interface:

•

Swipe down from the top of the screen or swipe left/right to go to the second idle screen.

•

Tap

Settings->Advanced

(default password: admin)

->Network->WAN Port->IPv4.

•

Tap the

Type

field.

•

Tap

Static IP

in the pop-up dialog box.

•

Enter the desired value in the

IP Address, Subnet Mask, Gateway, Primary DNS

and

Secondary DNS

field respectively.

•

Tap

to save the change or

to cancel.

You can configure a static IPv4 address for the IP phone. Before configuring it, make sure that the

mode

is configured as

IPv4

IPv4 & IPv6

To configure a static IPv6 address via phone user interface:

•

Swipe down from the top of the screen or swipe left/right to go to the second idle screen.

•

Tap

Settings->Advanced

(default password: admin)

->Network->WAN Port->IPv6.

•

Tap the

Type

field.

•

Tap

Static IP

in the pop-up dialog box.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands