Matrix SPARSH VP710 User Manual Download Page 659

Page: 659 / 1046

Matrix SPARSH VP710 User Guide

651

To configure DHCP VLAN discovery via web user interface:

•

Click on

Network->Advanced

•

In the

DHCP VLAN

block, select the desired value the

Active

list.

•

Enter the desired option in the

Option(1-255)

field.

The default option is 132.

•

Click

Confirm

to save the change.

A dialog box pops up to prompt that the settings will take effect after a reboot.

•

Click

to reboot the phone.

Local

Web User Interface

Configure DHCP VLAN discovery

feature.

Navigate to:

http://<phoneIPAddress>/

servlet?m=mod_data&p=network-
adv&q=load

Phone User Interface

Configure DHCP VLAN discovery

feature.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands