Matrix SPARSH VP710 User Manual Download Page 772

Page: 772 / 1046

764

Matrix SPARSH VP710 User Guide

Parameter

auto_provision.power_on

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to perform an auto
provisioning process when powered on.

Format

Boolean

Default Value

Range

Valid values are:

-Disabled

-Enabled

Example

auto_provision.power_on = 1

Parameter

auto_provision.repeat.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to check new
configuration repeatedly.

Format

Boolean

Default Value

Range

Valid values are:

-Disabled

Enabled

Example

auto_provision.repeat.enable = 0

Parameter

auto_provision.repeat.minutes

Configuration File

<MAC>.cfg

Description

Configures the interval (in minutes) for the IP phone
to check new configuration.

Note

: It works only if the parameter

“auto_provision.repeat.enable” is set to 1 (Enabled).

Format

Integer

Default Value

1440

Range

1 to 43200

Example

auto_provision.repeat.minutes = 1000

Parameter

auto_provision.weekly.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the IP phone to check new
configuration weekly.

Format

Boolean

Default Value

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 772 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: