Matrix SPARSH VP710 User Manual Download Page 478

Page: 478 / 1046

470

Matrix SPARSH VP710 User Guide

Voice mail access codes must be predefined on the system server. Contact your system administrator for
the more information.

Listening to Voice Mails

To listen to voice mails:

•

The touch screen prompts when the phone receives a new voice mail, press

or tap

Connect

to dial

out the voice mail access code.

•

Follow the voice prompt to listen to your voice mail.

Before listening to voice mails, ensure that the voice mail access code has been configured. For more
information, refer to

“Configuring the Voice Mail Access Codes”.

To view voice mails via phone user interface:

•

Swipe left or right to go to the second idle screen.

•

Tap

to launch

Message

application.

•

Tap

View Voice Mail

The touch screen displays the amount of new and old voice mails.

You can tap the account to listen to voice mails.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 478 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: