manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

340

Matrix SPARSH VP710 User Guide

If you stop transmitting video, the icon 

 

will display on the near-site video, as shown below: 

Your camera will not transmit video to your contact and the far site cannot see you.

Stopping transmitting video does not create an audio-only call. Even if you stop transmitting video, you can see the 
other party, and the call is still a video call. To place an audio-only call, contact your system administrator.

Changing the Video Layout during Calls

During video calls, near-site and far-site video images are displayed on the touch screen. You can change the 
video layout.

The system supports three video layouts:

•

One large, other small: One video image displays in a large size, the other video images along the right 

side of the screen displays in small sizes.

•

Full screen: One video image displays in full size, the other video images are hidden.

•

Same size: All video images display in the same size.

To swap video during a video call via phone user interface:

•

Tap the near-site (small window) video during a video call.

 

 

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

GAI-Tronics 1114 Installation And User Manual preview
1114
Brand: GAI-Tronics Pages: 32
Yezz F30 User Manual preview
F30
Brand: Yezz Pages: 15
Yealink Yealink SIP-T46G User Manual preview
Yealink SIP-T46G
Brand: Yealink Pages: 8
TCL 403 32GO BLEU Manual preview
403 32GO BLEU
Brand: TCL Pages: 34
Handspring Treo 300 Brochure preview
Treo 300
Brand: Handspring Pages: 2
Horizon Fitness Cisco 504 Administrator'S And User Manual preview
Cisco 504
Brand: Horizon Fitness Pages: 24
Pantech PG-1810 Service Manual preview
PG-1810
Brand: Pantech Pages: 54
M4 SS990 Quick Start Manual preview
SS990
Brand: M4 Pages: 22
Yealink Yealink T28P User Manual preview
Yealink T28P
Brand: Yealink Pages: 8
Opel mobile FlipPhone 4 Operator'S Manual preview
FlipPhone 4
Brand: Opel mobile Pages: 76
HTC Desire 628 Safety And Regulatory Manual preview
Desire 628
Brand: HTC Pages: 26
Mircom DTC-300A-2 Installation And Operation Manual preview
DTC-300A-2
Brand: Mircom Pages: 39
BT Home SmartPhone User Manual preview
Home SmartPhone
Brand: BT Pages: 8
HTC TyTN User Manual preview
TyTN
Brand: HTC Pages: 204
Pharos Traveler 137E User Manual preview
Traveler 137E
Brand: Pharos Pages: 104
Polycom VVX 5 Series Instructions preview
VVX 5 Series
Brand: Polycom Pages: 3
Zte Blade C342 User Manual preview
Blade C342
Brand: Zte Pages: 25
Zte Z730 Quick Start Manual preview
Z730
Brand: Zte Pages: 116

Brands by name

Popular brands

Load more brands