Matrix SPARSH VP710 User Manual Download Page 165 | Manualshive

Page: 165 / 1046

background image

Matrix SPARSH VP710 User Guide

157

•

Press

to adjust the notification sound.

•

Tap

OK

to accept the change or

Cancel

to cancel.

Notification sound is configurable via phone user interface only.

Silent Mode

If you turn on the silent mode, the IP phone won't produce ring tone/key tone/touch sound/notification sound from
phone's speaker.

You can use silent mode feature to block the incoming call/message from producing ring tone/notification tone from
phone's speaker. It is helpful for users not to be disturbed by the tone.

Procedure:

Silent Mode can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure the using permission of

silent mode feature.

For more information, refer

D - Configuration Parameters”

Local

Phone User Interface

Enable/Disable Silent Mode.

«
...
163
164
165
166
167
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

PhoneEasy 312cs

Brand: Doro Pages: 88

Brand: Denver Pages: 168

Brand: Yealink Pages: 8

Brand: Grandstream Networks Pages: 29

Brand: Gigaset Pages: 88

Brand: Brava Pages: 97

Brand: Verykool Pages: 30

Brand: ATCOM Pages: 10

Fanvil XU Series

Brand: dais Technology Partners Pages: 6

Brand: M2M Pages: 2

Brand: Samsung Pages: 183

Brand: Samsung Pages: 112

Brand: Samsung Pages: 153

Brand: Samsung Pages: 153

Brand: GE Pages: 2

Brand: GE Pages: 21

Blade V2020 Smart

Brand: Zte Pages: 4

ZENFONE 3 SERIES

Brand: Asus Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands