manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

681

Acoustic Clarity Technology

Acoustic Clarity Technology involves the following:

•

Acoustic Echo Cancellation

•

Background Noise Suppression

•

Automatic Gain Control

•

Voice Activity Detection

•

Comfort Noise Generation

•

Jitter Buffer

Acoustic Echo Cancellation

Acoustic Echo Cancellation (AEC) is used to reduce acoustic echo from a voice communication in order to improve 
the voice quality. It also increases the capacity achieved through silence suppression by preventing echo from 
traveling across the network.

The IP phone employs advanced acoustic echo cancellation for hands-free operation. Acoustic Echo Cancellation 
is normally not required for calls via the handset.In certain situations, where echo is experienced by the remote 
party, AEC may be used to reduce/avoid echo when the user uses the handset.

Utilizing acoustic echo cancellation will introduce a small delay increase into audio path which might cause 
a lower voice quality.

Procedure

AEC can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure 

acoustic echo 

cancellation

.

For more information, refer 

“Appendix D - Configuration 
Parameters”

.

Local

Web User Interface

Configure 

acoustic echo 

cancellation

Navigate to

:

http://<phoneIPAddress>/servlet?m

=mod_data&p=settings-voice&q=l

oad

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Aastra 6700i Series Configuration Manual preview
6700i Series
Brand: Aastra Pages: 27
Palm AT&T Treo 680 Starting Manual preview
AT&T Treo 680
Brand: Palm Pages: 52
Yealink MP50 Quick Start Manual preview
MP50
Brand: Yealink Pages: 8
Qing Xin Electronic V-18 User Manual preview
V-18
Brand: Qing Xin Electronic Pages: 45
Panasonic GSM900 Manual preview
GSM900
Brand: Panasonic Pages: 129
NAPCO StarLink SLE-LTE Commercial Series Installation Instructions Manual preview
StarLink SLE-LTE Commercial Series
Brand: NAPCO Pages: 20
Yealink W56B Quick Start Manual preview
W56B
Brand: Yealink Pages: 12
Blu Dash Music 2 User Manual preview
Dash Music 2
Brand: Blu Pages: 28
Sony Ericsson WT19a Troubleshooting Manual preview
WT19a
Brand: Sony Ericsson Pages: 15
Sony Ericsson T226s User Manual preview
T226s
Brand: Sony Ericsson Pages: 75
Mobistel Cynus T7 User Manual preview
Cynus T7
Brand: Mobistel Pages: 24
M4TEL M4 B3 Quick Start Manual preview
M4 B3
Brand: M4TEL Pages: 13
iBall Andi HD6 User Manual preview
Andi HD6
Brand: iBall Pages: 150
AKUA EK4e User Manual preview
EK4e
Brand: AKUA Pages: 34
Docomo P-06C Instruction Manual preview
P-06C
Brand: Docomo Pages: 162
GE 28223EE1 Specifications preview
28223EE1
Brand: GE Pages: 2
GE Cell Fusion 28129FE2 Specifications preview
Cell Fusion 28129FE2
Brand: GE Pages: 2
GE Cell Fusion 28127FE1 Specifications preview
Cell Fusion 28127FE1
Brand: GE Pages: 2

Brands by name

Popular brands

Load more brands