Matrix SPARSH VP710 User Manual Download Page 541

Page: 541 / 1046

Matrix SPARSH VP710 User Guide

533

•

Tap

Enabled

in the pop-up dialog box.

•

Tap

to save the change or

to cancel.

Keep Alive

IP phones can send keep-alive packets to the NAT device for keeping the communication port open.

Procedure

Keep alive feature can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure the type of keep-alive
packets on a per-line basis.

Configure the keep-alive interval on a
per-line basis.

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure the type of keep-alive

packets on a per-line basis.

Configure the keep-alive interval on a
per-line basis.

Navigate to:

http://<phoneIPAddress>/servlet?

m=mod_data&p=account-adv&q

=load&acc=0

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands