Matrix SPARSH VP710 User Manual Download Page 617

Page: 617 / 1046

Matrix SPARSH VP710 User Guide

609

To configure the shared line settings on alternate phone via web user interface:

•

(Enter the primary account 4609 in the Register Name field.)

•

Click on

Advanced

, select

Shared Call Appearance

from the

Shared Line

list.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands