Matrix SPARSH VP710 User Manual Download Page 993

Page: 993 / 1046

Matrix SPARSH VP710 User Guide

985

Dial Plan using Digit Map String Rules

Example

line.2.pickup_value = *88

Note:

This parameter only applies to BLF feature.

Parameter

linekey.X.label

Configuration File

<MAC>.cfg

Description

Configures the label displayed on the touch screen for
each DSS key.

For line keys:

X ranges from 1 to 27.

Default Value

Blank

Range

String within 99 characters

Example

line.2.pickup_value = *88

Note:

This parameter only applies to BLF feature.

Parameter

dialplan.digitmap.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the digit map feature for the IP
phone.

Default Value

Range

0-Disabled
1-Enabled

Note:

The value configured by the parameter

“account.X.dialplan.digitmap.enable” takes
precedence over that configured by this parameter

Example

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands