Matrix SPARSH VP710 User Manual Download Page 262 | Manualshive

Page: 262 / 1046

background image

254

Matrix SPARSH VP710 User Guide

•

Tap

Bluetooth

and then tap

Always

or

Just once

.

The IP phone scans and displays the available Bluetooth device automatically.

•

If there is no Bluetooth device found on the touch screen, tap

and then

Refresh

to search for the

Bluetooth devices.

If the Bluetooth mode of the IP phone is deactivated, the touch screen will prompt “To use Bluetooth
services, you must first turn on Bluetooth. Turn on Bluetooth now?”. Tap Turn on to activate the Bluetooth
mode.

•

Tap the desired Bluetooth device to share the pictures.

•

The touch screen will prompt “Sending n file to “XXX”” (n represents the number of pictures that is being

send).

•

Accept the Bluetooth file transfer request on the Bluetooth device.

«
...
260
261
262
263
264
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: i-mate Pages: 29

Brand: Samsung Pages: 252

Galaxy S20 FE 5G

Brand: Samsung Pages: 19

Galaxy S Epic SPH-D700

Brand: Samsung Pages: 264

Galaxy S II Skyrocket SGH-i727

Brand: Samsung Pages: 206

Galaxy S Plus GT-I9001

Brand: Samsung Pages: 147

Brand: Samsung Pages: 48

Galaxy J7 Prime

Brand: Samsung Pages: 33

Brand: Samsung Pages: 32

Brand: Samsung Pages: 2

Brand: Samsung Pages: 11

Brand: Samsung Pages: 2

Brand: Samsung Pages: 65

Brand: Samsung Pages: 2

Galaxy Amp Prime 3

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 163

Brand: Samsung Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands