manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

522

Matrix SPARSH VP710 User Guide

CDP

CDP (Cisco Discovery Protocol) allows the IP phone to receive and/or transmit device-related information from/to 
directly connected devices on the network that are also using the protocol, and store the information about other 
devices.
When CDP feature is enabled on the IP phone, the IP phone periodically advertise its own information to the 
directly connected CDP-enabled switch. The IP phone can also receive CDP packets from the connected switch. 
When the VLAN configurations on the IP phone are different from the ones sent by the switch, the IP phone 
perform an update and reboot. This allows the IP phone to be plugged into any switch, obtain their VLAN IDs, and 
then start communications with the call control.

Procedure

CDP can be configured using the configuration files or locally.

To configure CDP via web user interface:

•

Click on 

Network->Advanced.

•

In the 

CDP

 block, select the desired value from the 

Active

 list.

•

Enter the desired time interval in the 

Packet Interval (1~3600s)

 field.

•

Click 

Confirm

 to save the change.

Configuration File

<MAC>.cfg

Configure CDP feature.

For more information, refer 

“Appendix 

D - Configuration Parameters”

.

Local

Web User Interface

Configure CDP feature.

Navigate to:

http://<phoneIPAddress>/servlet?m

=mod_data&p=network-adv&q=load

Phone User Interface

Configure CDP feature.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

ZEN M27 Owner'S Manual preview
M27
Brand: ZEN Pages: 27
Iget blackview Crown Quick Start Manual preview
blackview Crown
Brand: Iget Pages: 76
i-mobile i-Style 8.1 User Manual preview
i-Style 8.1
Brand: i-mobile Pages: 58
TCL alcatel Pixi4-7 4G BELL Repair Document preview
alcatel Pixi4-7 4G BELL
Brand: TCL Pages: 41
TECNO MOBILE LIMITED CD8 User Manual preview
CD8
Brand: TECNO MOBILE LIMITED Pages: 6
Grandstream Networks GXV3350 Quick Installation Manual preview
GXV3350
Brand: Grandstream Networks Pages: 10
Ericsson CF888 User Manual preview
CF888
Brand: Ericsson Pages: 75
Spice C-5300 Manual preview
C-5300
Brand: Spice Pages: 21
NAPCO StarLink SLE-LTEV-SS Operating Instructions preview
StarLink SLE-LTEV-SS
Brand: NAPCO Pages: 2
Xiaomi Mi Mix 2S User Manual preview
Mi Mix 2S
Brand: Xiaomi Pages: 8
LG G7120 User Manual preview
G7120
Brand: LG Pages: 185
Billow S50VK User Manual preview
S50VK
Brand: Billow Pages: 102
AdvanceTec AdvanceCommunicator ATT3001A User Manual preview
AdvanceCommunicator ATT3001A
Brand: AdvanceTec Pages: 8
AMGOO AM530 Manual preview
AM530
Brand: AMGOO Pages: 11
Nokia 6124 classic User Manual preview
6124 classic
Brand: Nokia Pages: 63
Nokia 6185 - Cell Phone - CDMA Owner'S Manual preview
6185 - Cell Phone - CDMA
Brand: Nokia Pages: 105
Nokia 6233 - Cell Phone 6 MB User Manual preview
6233 - Cell Phone 6 MB
Brand: Nokia Pages: 123
Zte S226 User Manual preview
S226
Brand: Zte Pages: 36

Brands by name

Popular brands

Load more brands