Matrix SPARSH VP710 User Manual Download Page 756

Page: 756 / 1046

748

Matrix SPARSH VP710 User Guide

•

VAD, CNG, AEC, PLC, AJB, AGC

•

Full-duplex speakerphone with AEC

Video Features

•

Video codec: H264HP, H264, VP8

•

Image codec: JPEG, PNG, BMP

•

Adaptive bandwidth adjustment

Network Features

•

SIP v1 (RFC 2543), v2 (RFC 3261)

•

NAT Traversal: STUN mode

•

DTMF: INBAND, RFC 2833, SIP INFO

•

Proxy mode and peer-to-peer SIP link mode

•

IP assignment: Static/DHCP/PPPoE

•

VLAN assignment: LLDP/Static/DHCP/CDP

•

Bridge mode for PC port

•

HTTP/HTTPS server

•

DNS client

•

NAT/DHCP server

•

IPv6 support

•

Wi-Fi

Management

•

FTP/TFTP/HTTP/PnP auto-provision

•

Configuration: browser/phone/auto-provision

•

Direct IP call without SIP proxy

•

Dial number via SIP server

•

Dial URL via SIP server

•

TR-069

Security

•

HTTPS (server/client)

•

SRTP (RFC 3711)

•

Transport Layer Security (TLS)

•

VLAN (802.1q), QoS

•

Digest authentication using MD5/MD5-sess

•

Secure configuration file via AES encryption

•

Phone lock for personal privacy protection

•

Admin/User configuration mode

•

802.1X authentication

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 756 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: