Matrix SPARSH VP710 User Manual Download Page 106 | Manualshive

Page: 106 / 1046

background image

98

Matrix SPARSH VP710 User Guide

•

The default value is 10, you can set to 1-30.

•

Click

Confirm

to save the change.

Backlight

Backlight determines the brightness of the touch screen display, allowing users to read easily in dark environments.
Backlight time specifies the delay time to turn off the backlight when the IP phone is inactive. Backlight turns off
quickly if a short backlight time is configured, this may not give users enough time to read messages.

Backlight has two options:

•

Backlight Active Level:

The intensity of the touch screen when the phone is active. You can change the

intensity of the touch screen by dragging the backlight active level slider.

•

Backlight Time:

The delay time to change the intensity of the touch screen when the phone is inactive.

You can select a desired time to change the intensity or turn on the backlight permanently.

•

Always On:

Backlight is on permanently.

•

15s, 30s, 60s, 120s, 300s, 600s or 1800s:

Backlight is changed when the phone is inactive after the

designated time (in seconds).

«
...
104
105
106
107
108
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: Pantech Pages: 97

Brand: Pantech Pages: 52

Brand: Pantech Pages: 2

Yealink SIP-T48G

Brand: Yealink Pages: 2

Yealink SIP-T48G

Brand: Yealink Pages: 4

Yealink SIP-T46G

Brand: Yealink Pages: 38

Brand: Yealink Pages: 255

Yealink SIP-T48G

Brand: Yealink Pages: 105

Brand: Yealink Pages: 13

Brand: Yealink Pages: 77

Brand: 2N Pages: 32

Brand: meanIT Pages: 26

Brand: Homtom Pages: 15

Sphere AAP553G-315

Brand: Bauhn Pages: 40

Brand: UniData Communication Systems Pages: 41

Brand: Blaupunkt Pages: 38

Brand: Nodis Pages: 20

Brand: Grandstream Networks Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands