manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 963 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 963

Matrix SPARSH VP710 User Guide

955

Video Codecs

Range

0-Disabled
1-Enabled

If it is set to 0 (Disabled), video is not sent in outgoing 
calls and not received in incoming calls. All calls are 
audio-only.

If it is set to 1 (Enabled), video is sent in outgoing calls 
and received in incoming calls.

Example

NA

Parameter

-

camera.flicker

Configuration File

<MAC>.cfg

Description

Configures the value of camera flicker frequency (Hz).

Default Value

50

Range

50-50Hz
60-60Hz

Note: 

Indoor lights powered by a 50Hz or 60Hz power 

source can produce a flicker. You can adjust the camera 
flicker frequency according to the power source the 
light is powered by.

Example

NA

Parameter

-

account.X.video.<payload_type>.ena
ble

(where <payload_type> should be 
replaced by the name of video 
codec)

Configuration File

<MAC>.cfg

Description

Enables or disables the specified video codec for 
account X.

X ranges from 1 to 16

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments