manualshive.com logo in svg

Matrix SPARSH VP710, User Manual

The Matrix SPARSH VP710 User Manual is available for free download on our website. This comprehensive manual provides detailed instructions and guidelines to help you make the most of your VP710. Get the manual now from manualshive.com and unlock the full potential of this exceptional product.

Share
Download
background image

Matrix SPARSH VP710 User Guide

677

•

Repeat the above step to add more codecs to the 

Enable Codecs

 column.

•

To remove the codec from the 

Enable Codecs

 column, select the desired codec and then click 

.

•

To adjust the priority of codecs, select the desired codec and then click 

 or 

.

•

Click 

Confirm

 to save the change.

Packetization Time

Ptime (Packetization Time) is a measurement of the duration (in milliseconds) of the audio data in each RTP packet 
sent to the destination, and defines how much network bandwidth is used for the RTP stream transfer. Before 
establishing a conversation, codec and ptime are negotiated through SIP signaling. The valid values of ptime range 
from 10 to 60, in increments of 10 milliseconds. The default ptime is 20ms. You can also disable the ptime 
negotiation.

The following table summarizes the valid values of ptime for each audio codec:

Codec

Packetization Time (Minimun)

Packetization Time (Maximun)

G.722.1c(48kb/s)

20ms

60ms

G.722.1c(32kb/s)

20ms

60ms

G.722.1c(24kb/s)

20ms

60ms

G.722.1(24kb/s)

20ms

60ms

G722

10ms

40ms

PCMA

10ms

40ms

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Icemobile CHARM User Manual preview
CHARM
Brand: Icemobile Pages: 59
T-Mobile hiptop Manual preview
hiptop
Brand: T-Mobile Pages: 4
Samsung SM-T220 User Manual preview
SM-T220
Brand: Samsung Pages: 114
Samsung SGH-P408 User Manual preview
SGH-P408
Brand: Samsung Pages: 8
Samsung SCH-a610 Series Quick Reference Manual preview
SCH-a610 Series
Brand: Samsung Pages: 12
Samsung GT-S5830 Quick Start Manual preview
GT-S5830
Brand: Samsung Pages: 28
Samsung GT-I9100T Quick Start Manual preview
GT-I9100T
Brand: Samsung Pages: 28
Samsung GT-I8190 Quick Start Manual preview
GT-I8190
Brand: Samsung Pages: 35
meanIT SENIOR FLIP XL Manual preview
SENIOR FLIP XL
Brand: meanIT Pages: 26
Wileyfox Swift 2X User Manual preview
Swift 2X
Brand: Wileyfox Pages: 58
Manta CTA-5000 User Manual preview
CTA-5000
Brand: Manta Pages: 100
Olympia 9211 IP User Manual preview
9211 IP
Brand: Olympia Pages: 31
OUKITEL WP 6 Quick Start Manual preview
WP 6
Brand: OUKITEL Pages: 60
Ericsson T60d User Manual preview
T60d
Brand: Ericsson Pages: 101
Telecom ZIP 33i Quick Reference Manual preview
ZIP 33i
Brand: Telecom Pages: 2
Sedna SE-P1K User Manual preview
SE-P1K
Brand: Sedna Pages: 8
Zte Cricket Memo User Manual preview
Cricket Memo
Brand: Zte Pages: 62
KATA S60 User Manual preview
S60
Brand: KATA Pages: 45

Brands by name

Popular brands

Load more brands