Matrix SPARSH VP710 User Manual Download Page 104

Page: 104 / 1046

Matrix SPARSH VP710 User Guide

To enable the power saving feature via web user interface:

•

Click on

Settings->Power Saving.

•

Select

Enabled

from the

Power Saving

list.

Configuration File

<MAC>.cfg

Configure the power saving feature.

Configure the office hour.

Configure the idle timeout.

For more information, refer

“Appendix

D - Configuration Parameters”

Local

Web User Interface

Configure the power saving feature.

Configure the office hour.

Configure the idle timeout.

Navigate to

http://<phoneIPAddress>/
servlet?m=mod_d

ata&p=settings-powersaving&q=load

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands