Matrix SPARSH VP710 User Manual Download Page 537

Page: 537 / 1046

Matrix SPARSH VP710 User Guide

529

Procedure

NAT traversal and STUN server can be configured using the configuration files or locally.

Configuration File

<MAC>.cfg

Configure NAT traversal and STUN
server on the phone basis.

Configure local SIP port and TLS SIP

port.

Configure NAT traversal on a

per-line basis

For more information, refer

“Appendix D - Configuration
Parameters”

Local

Web User Interface

Configure NAT traversal and STUN
server.

Navigate to

http://<phoneIPAddress>/servlet?m

=mod_data&p=network-adv&q=load

Configure local SIP port and TLS SIP

port.

Navigate to:

http://<phoneIPAddress>/servlet?m

=mod_data&p=settings-sip&q=load

Configure NAT traversal on a per-line
basis.

Navigate to:

http://<phoneIPAddress>/servlet?m

=mod_data&p=account-register&q

=load&acc=0

Phone User Interface

Configure NAT traversal and STUN

server on a phone basis.

Configure NAT traversal on a per-line
basis.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands