Matrix SPARSH VP710 User Manual Download Page 706

Page: 706 / 1046

698

Matrix SPARSH VP710 User Guide

To configure RTP status displayed on the touch screen via web user interface:

•

Click on

Settings->Voice Monitoring

•

Select the desired value from the

Display Report options on phone

list

•

Click

Confirm

to save the change.

The RTP status will appear on the phone user interface at the path:

Settings->Status->RTP Status.

To configure the options of the RTP status displayed on the touch screen via web user interface:

•

Click on

Settings->Voice Monitoring.

•

In the

Report options on phone

block, select the desired list from the

Disabled

column and then click

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands