Matrix SPARSH VP710 User Manual Download Page 769

Page: 769 / 1046

Matrix SPARSH VP710 User Guide

761

PPPoE

Parameter

static.network.secondary_dns

Configuration File

<MAC>.cfg

Description

Configures the secondary IPv4 DNS server.

Note

: It works only if the value of the parameter

"static.network.static_dns_enable" is set to 1(On).

If you change this parameter, the IP phone will reboot
to make the change take effect.

Default Value

Blank

Range

IPv4 Address

Example

static.network.secondary_dns = 202.101.103.54

Parameter

static.network.internet_port.type

Configuration File

<MAC>.cfg

Description

Configures the Internet port type

Note

: It works only if the value of the parameter

“static.network.ip_address_mode” is set to

0 (IPv4) or 2 (IPv4 & IPv6). If you change this
parameter, the IP phone will reboot to make

the change take effect.

Default Value

Range

Valid values are:

-DHCP

-PPPoE

-Static IP Address

Example

static.network.internet_port.type = 1

Parameter

static.network.pppoe.user

Configuration File

<MAC>.cfg

Description

Configures the PPPoE username when the Internet port
type is configured as PPPoE and the IP address mode is
configured as IPv4 or IPv4&IPv6

Note

: If you change this parameter, the IP phone will

reboot to make the change take effect.

Default Value

Blank

Range

String within 32 characters

Example

static.network.pppoe.user = test.matrix

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands