Matrix SPARSH VP710 User Manual Download Page 100

Page: 100 / 1046

Matrix SPARSH VP710 User Guide

•

Tap

on the top-left of the touch screen.

Do one of the following:

•

Tap

Images

to see all pictures stored in internal SD card or USB flash drive (if connected).

•

Tap

Downloads

to see all pictures you have downloaded.

•

Tap

Gallery

to see all pictures by Gallery application.

Select a desired picture to preview.

The picture will appear in the recently used wallpapers list.

•

Tap

Set wallpaper.

You can also long tap the empty spot on the idle screen and then tap

WALLPAPERS

, the effect is equal to tapping

Settings->Basic->Display->Wallpaper->Wallpapers

. Then you can change the phone wallpaper as per the

instructions mentioned above.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 100 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: