Matrix SPARSH VP710 User Manual Download Page 55

Page: 55 / 1046

Matrix SPARSH VP710 User Guide

To view the phone status via web user interface:

•

Open the web browser of your computer.

•

Enter the IP address in the browser’s address bar, and then press

Enter

•

Enter the

Username

(

admin

) and

Password

(default:

admin

) in the login page.

•

Click

Confirm

to login.

The phone status is displayed on the first page of the web user interface.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands