Matrix SPARSH VP710 User Manual Download Page 582 | Manualshive

Page: 582 / 1046

background image

574

Matrix SPARSH VP710 User Guide

To configure paging list via phone user interface:

•

Tap the paging list key when the phone is idle.

If the paging list key is not configured, you can also swipe down from the top of the screen or swipe left/
right to go to the second idle screen.
Then tap

Settings->Features->Paging List

to configure the paging list.

•

Tap

after the desired paging group.

•

Enter the multicast IP address and port number (e.g., 224.5.6.20:10008) in the

Address

field.

The valid multicast IP addresses range from 224.0.0.0 to 239.255.255.255.

•

Enter the paging group name in the

Label

field.

•

Enter the desired channel in the

Channel

field

The valid channel ranges from 0 to 30.

•

Tap

to save the change or

to cancel.

•

Repeat the above5 steps to add more paging groups.

«
...
580
581
582
583
584
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SPARSH VP710

Brand: Samsung Pages: 2

Brand: Samsung Pages: 62

Brand: Samsung Pages: 48

Brand: Samsung Pages: 33

Brand: Samsung Pages: 2

Focus S SGH-I937

Brand: Samsung Pages: 175

Brand: Samsung Pages: 2

Brand: Samsung Pages: 24

Brand: Samsung Pages: 2

Brand: Samsung Pages: 145

Brand: Samsung Pages: 167

Brand: Obihai Pages: 12

Brand: Obihai Pages: 220

Brand: TCM Mobile Pages: 37

Brand: Doogee Pages: 8

Brand: Sony Ericsson Pages: 75

Brand: Ulefone Pages: 47

Brand: Grandstream Networks Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands