Matrix SPARSH VP710 User Manual Download Page 73

Page: 73 / 1046

Matrix SPARSH VP710 User Guide

To configure DHCP via web user interface:

•

Click on

Network->Basic

•

In the

IPv4 Config

block, click

DHCP

•

Click

Confirm

to save the change.

A dialog box pops up to prompt that settings will take effect after a reboot.

•

Click

to reboot the IP phone.

To configure static DNS address when DHCP is used via web user interface:

•

Click on

Network->Basic

•

In the

IPv4 Config

block, click

DHCP

•

Click

Static DNS

Local

Web User Interface

Configure DHCP on the IP phone.

Configure static DNS address when
DHCP is used.

Navigate to

http://<phoneIPAddress>/
servlet?m=mod_dat

a&p=network&q=load

Phone User Interface

Configure DHCP on the IP phone.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands