manualshive.com logo in svg

Matrix SPARSH VP710, User Manual, Page: 699 / 1046

Share
Download
Matrix SPARSH VP710 User Manual Download Page 699

Matrix SPARSH VP710 User Guide

691

CHAPTER 13

Voice Quality Monitoring 

(VQM)

Voice quality monitoring allows the IP phone to generate various quality metrics for listening and conversational 
quality. These metrics can be sent between the phones in RTCP-XR packets. These metrics can also be sent in 
SIP PUBLISH messages to a central voice quality report collector.

Two mechanisms for voice quality monitoring supported by the IP phone:

•

RTCP-XR

•

VQ-RTCPXR

RTCP-XR

The RTCP-XR mechanism compliant with RFC 3611- RTP Control Extended Reports (RTCP XR) provides the 
metrics contained in RTCP-XR packets for monitoring the quality of the calls. These metrics include network packet 
loss, delay metrics, analog metrics and voice quality metrics.

Procedure

RTCP-XR can be configured using the configuration files or locally.

VQ-RTCPXR

The VQ-RTCPXR mechanism compliant with RFC 6035 sends the service quality metric reports contained in SIP 
PUBLISH messages to the central report collector. 

Three types of quality reports can be enabled:

•

Session

: Generated at the end of a call.

•

Interval

: Generated during a call at a configurable period.

•

Alert

: Generated when the call quality degrades below a configurable threshold.

Configuration File

<MAC>.cfg

Configure RTCP-XR.

For more information, refer 

“Appendix D - Configuration 
Parameters”

.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments