Matrix SPARSH VP710 User Manual Download Page 427

Page: 427 / 1046

Matrix SPARSH VP710 User Guide

419

To perform a blind transfer, do one of the following:

•

When there is an active call for the account selected from the

Account ID

field on the speed dial or BLF

key. Drag the far-site window to that speed dial or BLF key

Then the call is connected to the number specified in the

Value

field of the speed dial or BLF key. For more

information on how to configure a speed dial or BLF key, refer to

“DSS Keys”

•

Make sure you have an active call and one or more calls on hold, drag one far-site window to another far-

site window.

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Matrix SPARSH VP710, User Manual, Page: 427 / 1046

Search results

Summary of Contents for SPARSH VP710

Reviews: