Matrix SPARSH VP710 User Manual Download Page 974

Page: 974 / 1046

966

Matrix SPARSH VP710 User Guide

Parameter

phone_setting.vq_rtcpxr_display_pa
ckets_lost.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the phone to display Packets Lost
on the touch screen.

Default Value

Range

0-Disabled
1-Enabled

Note:

It works only if the value of the parameter

“phone_setting.vq_rtcpxr.states_show_on_gui.enable
” is set to 1 (Enabled).

Example

Parameter

phone_setting.vq_rtcpxr_display_sy
mm_oneway_delay.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the phone to display
SymmOneWayDelay on the touch screen.

Default Value

Range

0-Disabled
1-Enabled

Note:

It works only if the value of the parameter

“phone_setting.vq_rtcpxr.states_show_on_gui.enable
” is set to 1 (Enabled).

Example

Parameter

phone_setting.vq_rtcpxr_display_ro
und_trip_delay.enable

Configuration File

<MAC>.cfg

Description

Enables or disables the phone to display
RoundTripDelay on the touch screen.

Default Value

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands

Matrix SPARSH VP710, User Manual

Search results

Summary of Contents for SPARSH VP710

Reviews:

Related manuals for SPARSH VP710

Brands by name

Popular brands