Home
/
Matrix
/
SPARSH VP710
/
User Manual

Matrix SPARSH VP710, User Manual, Page: 152 / 1046

Share

Page: 152 / 1046

Matrix SPARSH VP710 User Manual Download Page 152

144

Matrix SPARSH VP710 User Guide

•

Select the desired value from the

Call Information Display Method

list.

•

Click

Confirm

to save the change.

Display Method on Dialing

When the IP phone is on the pre-dialing or dialing screen, the account information will be displayed on the top-left
corner of the touch screen.

You can customize the account information to be displayed on the IP phone as required. IP phones support three
account information display methods: Label, Display Name or User Name.

To configure display method on dialing via web user interface:

•

Click on

Features->General Information.

•

Select the desired value from the

Display Method on Dialing

list.

•

Click

Confirm

to save the change.

«
...
150
151
152
153
154
...
»

Summary of Contents for SPARSH VP710























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments