4E-10 ABS:
DTC Check
S6RW0C4504004
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(1).
Special tool
(A): SUZUKI scan tool
3) Turn ignition switch to ON position.
4) Read DTC according to instructions displayed on
SUZUKI scan tool and print it or write it down. Refer
to SUZUKI scan tool operator’s manual for further
details.
NOTE
If SUZUKI scan tool can not communicate
ABS hydraulic unit / control module, perform
“Serial Data Link Circuit Check”.
5) After completing the check, turn ignition switch off
and disconnect SUZUKI scan tool from DLC.
DTC Table
S6RW0C4504005
CAUTION
!
Be sure to perform “ABS Check” before
starting diagnosis.
DTC Clearance
S6RW0C4504006
WARNING
!
When performing a driving test, select a safe
place where there is neither any traffic nor
any traffic accident possibility and be very
careful during testing to avoid occurrence of
an accident.
After repair or replace malfunction part(s), clear all DTCs
by performing the following procedure or using SUZUKI
scan tool.
1) Connect SUZUKI scan tool to data link connector in
the same manner as when making this connection
for DTC check.
2) Turn ignition switch to ON position.
3) Erase DTC according to instructions displayed on
scan tool. Refer to scan tool operator’s manual for
further derails.
NOTE
For DTC C1022, C1026, C1032, C1036 and
C1061, confirm that ABS warning light turns
off after performing Step 2 of “Test Driving”
under “ABS Check”, and then clear the DTCs.
4) After completing the clearance, turn ignition switch
OFF and disconnect scan tool from data link
connector.
5) Perform “Driving Test” (Step 2 of “ABS Check”) and
“DTC Check” and confirm that NO DTC is displayed
on scan tool.
DTC (displayed on
SUZUKI scan tool)
Diagnostic Items
NO DTC
Normal
)
C1013
Control module mismatch
)
C1015
G sensor circuit (for 4WD model)
)
C1016
Brake light switch
)
C1021
RF
Wheel speed sensor circuit
)
C1025
LF
)
C1031
RR
)
C1035
LR
)
C1022
RF
Wheel speed sensor or
encoder
)
C1026
LF
)
C1032
RR
)
C1036
LR
)
C1033
Wheel speed sensor deviation
(A)
1
I5RW0A450007-01
)
C1041
RF
Inlet solenoid
)
C1045
LF
)
C1051
RR
)
C1055
LR
)
C1042
RF
Outlet solenoid
)
C1046
LF
)
C1052
RR
)
C1056
LR
)
C1057
Power supply voltage too high / too
low
)
C1061
Pump motor circuit
)
C1063
Solenoid valve power supply driver
circuit
)
C1071
Control module internal defect
DTC (displayed on
SUZUKI scan tool)
Diagnostic Items
Summary of Contents for 2006 SX4
