manualshive.com logo in svg

NXP Semiconductors Kinetis KE1xZ256, Reference Manual

The NXP Semiconductors Kinetis KE1xZ256 is a high-performance microcontroller ideal for a wide range of embedded applications. For comprehensive guidance on using this powerful device, download the Reference Manual for free from the official NXP website. Access detailed instructions and specifications to optimize your project's performance.

Share
Download
background image

13.4.4 Performance

This section addresses the performance of the eDMA module, focusing on two separate
metrics:

• In the traditional data movement context, performance is best expressed as the peak

data transfer rates achieved using the eDMA. In most implementations, this transfer
rate is limited by the speed of the source and destination address spaces.

• In a second context where device-paced movement of single data values to/from

peripherals is dominant, a measure of the requests that can be serviced in a fixed time
is a more relevant metric. In this environment, the speed of the source and destination
address spaces remains important. However, the microarchitecture of the eDMA also
factors significantly into the resulting metric.

13.4.4.1 Peak transfer rates

The peak transfer rates for several different source and destination transfers are shown in
the following tables. These tables assume:

• Internal SRAM can be accessed with zero wait-states when viewed from the system

bus data phase

• All internal peripheral bus reads require two wait-states, and internal peripheral bus

writes three wait-states, when viewed from the system bus data phase

• All internal peripheral bus accesses are 32-bits in size

NOTE

All architectures will not meet the assumptions listed above.
See the SRAM configuration section for more information.

This table compares peak transfer rates based on different possible system speeds.
Specific chips/devices may not support all system speeds listed.

Table 13-4. eDMA peak transfer rates (Mbytes/sec)

System Speed, Width

Internal SRAM-to-

Internal SRAM

32 bit internal peripheral

bus-to-Internal SRAM

Internal SRAM-to-32 bit

internal peripheral bus

48 MHz, 32 bit

96.0

48.0

38.4

66.7 MHz, 32 bit

133.3

66.7

53.3

83.3 MHz, 32 bit

166.7

83.3

66.7

100.0 MHz, 32 bit

200.0

100.0

80.0

133.3 MHz, 32 bit

266.7

133.3

106.7

150.0 MHz, 32 bit

300.0

150.0

120.0

Chapter 13 Enhanced Direct Memory Access (eDMA)

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

NXP Semiconductors

247

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Caen V793 Technical Information Manual preview
V793
Brand: Caen Pages: 20
Parkside PDWE 8 A2 Operation And Safety Notes Translation Of The Original Instructions preview
PDWE 8 A2
Brand: Parkside Pages: 65
Rayrun T112 Quick Start Manual preview
T112
Brand: Rayrun Pages: 4
Parker ET Series Maintenance Instructions & Parts List preview
ET Series
Brand: Parker Pages: 29
ZKTeco C3 Pro Quick Start Manual preview
C3 Pro
Brand: ZKTeco Pages: 43
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Brand: Invertek Pages: 5
Techtrol TLIC Instruction And Programming Manual preview
TLIC
Brand: Techtrol Pages: 4
Swagelok KPF Series Maintenance Instructions Manual preview
KPF Series
Brand: Swagelok Pages: 6
meibes SOL-BASIS Commissioning Manual preview
SOL-BASIS
Brand: meibes Pages: 20
Telit Wireless Solutions EVK Series User Manual preview
EVK Series
Brand: Telit Wireless Solutions Pages: 49
Omega CN32Pt User Manual preview
CN32Pt
Brand: Omega Pages: 20
Instruments of Things IO-Lights User Manual preview
IO-Lights
Brand: Instruments of Things Pages: 12
S&P REB 1 Manual preview
REB 1
Brand: S&P Pages: 8
Danfoss AMD 610 AS Installation Manual preview
AMD 610 AS
Brand: Danfoss Pages: 2
Walchem W600 Series Instruction Manual preview
W600 Series
Brand: Walchem Pages: 88
Infineon XDPL8220 Getting Started preview
XDPL8220
Brand: Infineon Pages: 14
Keysight N4965A Getting Started Manual preview
N4965A
Brand: Keysight Pages: 22
National Instruments cRIO-9030 Getting Started Manual preview
cRIO-9030
Brand: National Instruments Pages: 18

Brands by name

Popular brands

Load more brands