NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 1141 | Manualshive

Page: 1141 / 1325

background image

LPI2Cx_MCFGR1 field descriptions (continued)

Field

Description

110

Divide by 64.

111

Divide by 128.

45.3.9 Master Configuration Register 2 (LPI2Cx_MCFGR2)

The MCFGR2 should only be written when the I2C Master is disabled.

Address: Base a 28h offset

Bit 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10

9

8

7

6

5

4

3

2

1

0

R

W

Reset

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

LPI2Cx_MCFGR2 field descriptions

Field

Description

31–28

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

27–24

FILTSDA

Glitch Filter SDA

Configures the I2C master digital glitch filters for SDA input, a configuration of 0 will disable the glitch filter.
Glitches equal to or less than FILTSDA cycles long will be filtered out and ignored. The latency through
the glitch filter is equal to FILTSDA cycles and must be configured less than the minimum SCL low or high
period.

The glitch filter cycle count is not affected by the PRESCALE configuration and is automatically bypassed
in High Speed mode.

23–20

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

19–16

FILTSCL

Glitch Filter SCL

Configures the I2C master digital glitch filters for SCL input, a configuration of 0 will disable the glitch filter.
Glitches equal to or less than FILTSCL cycles long will be filtered out and ignored. The latency through the
glitch filter is equal to FILTSCL cycles and must be configured less than the minimum SCL low or high
period.

The glitch filter cycle count is not affected by the PRESCALE configuration and is automatically bypassed
in High Speed mode.

15–12

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

BUSIDLE

Bus Idle Timeout

Configures the bus idle timeout period in clock cycles. If both SCL and SDA are high for longer than
BUSIDLE cycles, then the I2C bus is assumed to be idle and the master can generate a START condition.
When set to zero, this feature is disabled.

Chapter 45 Low Power Inter-Integrated Circuit (LPI2C)

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

NXP Semiconductors

1141

«
...
1139
1140
1141
1142
1143
...
»

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Brand: Hable Pages: 3

Brand: Calsense Pages: 74

Brand: Zeagle Pages: 37

Brand: Garmin Pages: 4

Brand: KEB Pages: 16

Brand: RAM Pages: 71

Brand: Xilinx Pages: 101

Brand: H3C Pages: 48

Brand: Vector Pages: 22

Brand: SSHC Pages: 2

Brand: aldes Pages: 3

Domotion DLC-4 RGBW

Brand: Artecta Pages: 12

Brand: Whelen Engineering Company Pages: 10

Meridian MEC-110

Brand: FASTRON. Pages: 12

Brand: Danfoss Pages: 72

Brand: Computherm Pages: 12

MontBlanc KOSMOS CRUX-D

Brand: Kohzu Precision Pages: 74

Brand: Matelec Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands