NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 246 | Manualshive

Page: 246 / 1325

background image

software must handle the context of the cancel. If an interrupt is
desired (or not), then the interrupt should be enabled (or
disabled) before the cancel request. The application software
must clean up the transfer control descriptor since the full
transfer did not occur.

The occurrence of any error causes the eDMA engine to stop normal processing of the
active channel immediately (it goes to its error processing states and the transaction to the
system bus still has pipeline effect), and the appropriate channel bit in the eDMA error
register is asserted. At the same time, the details of the error condition are loaded into the
Error Status register (DMAx_ES). The major loop complete indicators, setting the
transfer control descriptor DONE flag and the possible assertion of an interrupt request,
are not affected when an error is detected. After the error status has been updated, the
eDMA engine continues operating by servicing the next appropriate channel. A channel
that experiences an error condition is not automatically disabled. If a channel is
terminated by an error and then issues another service request before the error is fixed,
that channel executes and terminates with the same error condition.

13.4.3 Channel preemption

Channel preemption is enabled on a per-channel basis by setting the DCHPRIn[ECP] bit.
Channel preemption allows the executing channel’s data transfers to temporarily suspend
in favor of starting a higher priority channel. After the preempting channel has completed
all its minor loop data transfers, the preempted channel is restored and resumes
execution. After the restored channel completes one read/write sequence, it is again
eligible for preemption. If any higher priority channel is requesting service, the restored
channel is suspended and the higher priority channel is serviced. Nested preemption, that
is, attempting to preempt a preempting channel, is not supported. After a preempting
channel begins execution, it cannot be preempted. Preemption is available only when
fixed arbitration is selected.

A channel’s ability to preempt another channel can be disabled by setting
DCHPRIn[DPA]. When a channel’s preempt ability is disabled, that channel cannot
suspend a lower priority channel’s data transfer, regardless of the lower priority channel’s
ECP setting. This allows for a pool of low priority, large data-moving channels to be
defined. These low priority channels can be configured to not preempt each other, thus
preventing a low priority channel from consuming the preempt slot normally available to
a true, high priority channel.

Functional description

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

246

NXP Semiconductors

«
...
244
245
246
247
248
...
»

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Brand: Vacon Pages: 62

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: Taco Electronic Solutions Pages: 28

Brand: Dahua Pages: 137

Extra Free RZB-02

Brand: Zamel Pages: 2

Brand: Jetter Pages: 24

Brand: I-Tork Pages: 15

Brand: Danfoss Pages: 8

total control MRX-10

Brand: Universal Remote Control Pages: 16

Brand: SAMES KREMLIN Pages: 5

Brand: NEC Pages: 852

Brand: Uniteck Pages: 46

Brand: SUPMEA Pages: 32

Brand: METRON Pages: 34

Brand: NELSEN WATER Pages: 16

Thermo Call TC3

Brand: Webasto Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands