manualshive.com logo in svg

NXP Semiconductors Kinetis KE1xZ256, Reference Manual

Share
Download
NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 1254

Table 47-6. SPI Master (CPHA=0) Configuration (continued)

Register

Value

Comments

SHIFTCTL(n+1)

0x0000_0101

Configure receive using Timer 0 on

posedge of clock with input data on Pin

1.

TIMCMPn

0x0000_3F01

Configure 32-bit transfer with baud rate

of divide by 4 of the FlexIO clock. Set

TIMCMP[15:8] = (number of bits x 2) - 1.

Set TIMCMP[7:0] = (baud rate divider /

2) - 1.

TIMCFGn

0x0100_2222

Configure start bit, stop bit, enable on

trigger high and disable on compare,

initial clock state is logic 0. Set PINPOL

to invert the output shift clock.

TIMCTLn

0x01C3_0201

Configure dual 8-bit counter using Pin 2

output (shift clock), with Shifter 0 flag as

the inverted trigger.

TIMCMP(n+1)

0x0000_FFFF

Never compare.

TIMCFG(n+1)

0x0000_1100

Enable when Timer 0 is enabled and

disable when Timer 0 is disabled.

TIMCTL(n+1)

0x0003_0383

Configure 16-bit counter (never

compare) using inverted Pin 3 output (as

slave select).

SHIFTBUFn

Data to transmit

Transmit data can be written to

SHIFTBUF, use the Shifter Status Flag

to indicate when data can be written
using interrupt or DMA request. Can

support MSB first transfer by writing to

SHIFTBUFBBS register instead.

SHIFTBUF(n+1)

Data to receive

Received data can be read from

SHIFTBUFBYS, use the Shifter Status

Flag to indicate when data can be read

using interrupt or DMA request. Can

support MSB first transfer by reading

from SHIFTBUFBIS register instead.

Table 47-7. SPI Master (CPHA=1) Configuration

Register

Value

Comments

SHIFTCFGn

0x0000_0021

Start bit loads data on first shift.

SHIFTCTLn

0x0003_0002

Configure transmit using Timer 0 on

posedge of clock with output data on Pin

0.

SHIFTCFG(n+1)

0x0000_0000

Start and stop bit disabled.

SHIFTCTL(n+1)

0x0080_0101

Configure receive using Timer 0 on

negedge of clock with input data on Pin

1.

TIMCMPn

0x0000_3F01

Configure 32-bit transfer with baud rate

of divide by 4 of the FlexIO clock. Set

TIMCMP[15:8] = (number of bits x 2) - 1.

Table continues on the next page...

Application Information

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

1254

NXP Semiconductors

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands