NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 1246 | Manualshive

Page: 1246 / 1325

background image

The Shifter Status Flag (SHIFTSTAT[SSF]) and any enabled interrupts or DMA requests
will set when data has been loaded from the SHIFTBUF register into the Shifter or when
the Shifter is initially configured into Transmit mode. The flag will clear when new data
has been written into the SHIFTBUF register.

The Shifter Error Flag (SHIFTERR[SEF]) and any enabled interrupts will set when an
attempt to load data from an empty SHIFTBUF register occurs (buffer underrun). The
flag can be cleared by writing it with logic 1.

47.4.1.2 Receive Mode

When configured for Receive mode (SHIFTCTL[SMOD]=Receive), the shifter will shift
data in and store data into the SHIFTBUF register when a store event is signalled by the
assigned Timer. Checking for a start/stop bit can be enabled before/after shifter data is
sampled by configuring the SHIFTCFG[SSTART], TIMCFG[TSTART] or
SHIFTCFG[SSTOP], TIMCFG[TSTOP] registers in the Shifter and Timer.

The Shifter Status Flag (SHIFTSTAT[SSF]) and any enabled interrupts or DMA requests
will set when data has been stored into the SHIFTBUF register from the Shifter. The flag
will clear when the data has been read from the SHIFTBUF register.

The Shifter Error Flag (SHIFTERR[SEF]) and any enabled interrupts will set when an
attempt to store data into a full SHIFTBUF register occurs (buffer overrun) or when a
mismatch occurs on a start/stop bit check. The flag can be cleared by writing it with logic
1.

47.4.1.3 Match Store Mode

When configured for Match Store mode (SHIFTCTL[SMOD]=Match Store), the shifter
will shift data in, check for a match result and store matched data into the SHIFTBUF
register when a store event is signalled by the assigned Timer. Checking for a start/stop
bit can be enabled before/after shifter data is sampled by configuring the
SHIFTCFG[SSTART], TIMCFG[TSTART] or SHIFTCFG[SSTOP], TIMCFG[TSTOP]
registers in the Shifter and Timer. Up to 16-bits of data can be compared using
SHIFTBUF[31:16] to configure the data to be matched and SHIFTBUF[15:0] to mask the
match result.

The Shifter Status Flag (SHIFTSTAT[SSF]) and any enabled interrupts or DMA requests
will set when a match occurs and matched data has been stored into the SHIFTBUF
register from the Shifter. The flag will clear when the matched data has been read from
the SHIFTBUF register.

Functional description

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

1246

NXP Semiconductors

«
...
1244
1245
1246
1247
1248
...
»

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Brand: D-Link Pages: 113

Brand: D-Link Pages: 146

Brand: TEL Pages: 26

Brand: Vimar Pages: 32

Brand: Sartorius Pages: 165

Brand: Therma-Stor Pages: 20

SR-ZG9001T-RGBW

Brand: Sunricher Pages: 3

Brand: Shimaden Pages: 16

Brand: Sturtevant Richmont Pages: 73

Brand: NDS Pages: 20

Brand: PI Pages: 111

Brand: Watt Stopper Pages: 3

BMS NUV100-CI-12

Brand: Nuvation Pages: 41

Brand: National Instruments Pages: 100

Brand: YASKAWA Pages: 282

Brand: Fairchild Pages: 4

HYGRASREG KH-10

Brand: S+S Regeltechnik Pages: 16

Brand: Freescale Semiconductor Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands