Alcatel Omni Switch/Router, User Manual

Page: 861 / 1100

The WAN Port Software Menu
Page 28-35
ISDN-BRI Port Example
The following example displays the configuration view screen for an ISDN-BRI port (port 2).
To view 3/2, enter:
wpview 3/2
or
wpv 3/2
A screen similar to following displays:
Configuration View for Slot 3, Port 2.
1)
Admin Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UP
2) Speed in BPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2048000
3) Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Split
4) Protocol Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frame Relay
8) TOS for Voice Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . a0
9) TOS for Voice Signaling Data . . . . . . . . . . . . . . . . . . . . . . . . 60
10) TOS Mask for both TOS Value. . . . . . . . . . . . . . . . . . . . . . . . e0
11) Signaling IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0.0.0
12) Signaling IP Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255.255.255.255
13) KeepAlive Up Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
14) KeepAlive Down Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
15) KeepAlive Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
16) DTR Pulse Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
17) DTR Pulse Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0
♦
Note
♦
The ISDN
wpview
menu displays PPP specific line
options described in the section Modifying a Port on
page 28-14. However, they do not apply to an ISDN
port, and are not described below.
Admin Status
The options for the Admin Status are
UP
and
DN
. If
UP
, the port has been enabled and
can transmit data as long as its Operational Status is also
UP
. If set to
DN
, the port will not
pass data even if its physical connection is good.
Speed in BPS
This field displays the access rate for the Frame Relay line to the service provider. This
parameter is the speed of the entire connection, not an individual virtual circuit. For
example, if you have a 56 kbps line to your service provider, this field should be set to
56000. A full T1 line would have an access rate of 1,544,000 bps, and a full E1 line would
have an access rate of 2,048,000 bps. For either T1 or E1, you can also have a fractional
service with an access rate that is a multiple of 64 kbps.
Clocking
This field displays either
External
,
Internal
, or
Split
. For a more detailed discussion of
clocking, see Clocking under Modifying a Port on page 28-14.
Protocol Type
The protocol type can be set to either Frame Relay or Point to Point Protocol (PPP). The
default setting is Frame Relay.