View Switch-Level Statistics
Page 11-6
Setting the Sampling Interval
The sampling interval is the time interval between polls of the switch’s consumable resources
to see if it is performing within the set thresholds. To set the amount of time between polls:
1.
Enter
health
at a system prompt. The health menu (described above) displays.
2.
Enter a
3
at the health menu prompt. The following menu displays:
Resource Monitoring Interval Configuration
1) Sampling Interval
: 5
3.
To change the sampling interval, enter a 1, and equal sign, and the new interval in
seconds. For example, to change the sampling interval to 4 seconds, you would enter the
following:
1=4
4.
When you have finished entering the new value, you must enter
save
to keep the new
configuration setting.
Sampling Interval
This sets the number of seconds between internal polling intervals. The health statistics
compares the current poll statistics with the last poll statistics to determine whether or not to
send a trap. The default for the
Sampling Interval
is five (5) seconds.
View Switch-Level Statistics
To view the statistics for the entire switch, enter the
hdstat
command at a system prompt. The
following table is displayed:
Device
1 Min
1 Hr
1 Hr
Resources
Limit
Curr
Avg
Avg
Max
----------------
--------
-------
--------
------
------
Receive
80
00
00
00
00
Transmit/Receive
80
00
00
00
00
Backplane
80
01
01
01
01
CAM [MPM]
80
00
00
00
00
CAM [HRE]
80
00
00
00
00
CPU
80
93*
13
13
22
Memory
80
50
50
50
50
Temperature
45
44
44
44
44
Virtual Ports
80
11
11
11
11
/System/Health %
Statistics are displayed as percentages of the total resource capacity, and represent data taken
from the last sampling interval. If a threshold for a resource was exceeded, then that statistic
is marked with an asterisk (*).
♦
Important Note
♦
The
hdstat
command displays CAM usage for the entire
chassis. To see CAM usage for switching modules only,
use the
camstat
command as described in Chapter 9,
“Switch Wide Parameters.”
Summary of Contents for Omni Switch/Router
