![background image](http://html1.mh-extra.com/html/ryobi/rdp102l/rdp102l_manual_1504970018.webp)
WARNING
Always wear safety goggles or safety glasses with
side shields when operating power tools. Failure to
do so could result in objects being thrown into your
eyes resulting in possible serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of the product.
The use of attachments or accessories not
recommended can result in serious personal injury.
WARNING
To avoid possible injury, keep guard closed and in
place while tool is in operation.
CHANGING SPEEDS AND BELT PLACEMENT
See Figure 24.
The spindle speed is determined by the location of the
belt on the pulleys inside the head assembly. The speed
chart located on the cover inside the head assembly
shows the recommended speed and pulley con
fi
guration
for each drilling operation.
To change the pulley con
fi
guration:
1. Lift pulley cover.
2. Loosen the tension bolt.
3. Remove the belt.
4. Reposition the belt according to the speed chart.
5. Retighten the tension bolt.
NOTE:
Refer to the "Recommended Drilling
Speed" section for size of drill bit and drilling speed
recommendations.
RECOMMENDED DRILLING SPEED
DRILLING SPEED TABLE (RPM)
Drill bit
diameter
(Inches)
Material
Wood
Plastics
Aluminium
Zinc
Brass
Iron
Steel
1/16
2430
2430
2430
1/8
1800
3/16
1300
1/4
1800
5/16
800
3/8
1300
1/2
1800
800
510
ON/OFF switch
See Figure 25.
To turn the drill press on:
1. Press the ON button ( l ).
To turn the drill press o
ff
:
1. Press the OFF button ( O ).
WARNING
Always make sure the workpiece is not in contact with
the bit before operating the switch to start the product.
Failure to heed this warning may cause the workpiece
to be kicked back toward the operator and result in
serious personal injury.
INSTALLING AND REMOVING BITS
See Figure 26.
1. Unplug the drill press.
2. Open or close the chuck jaws to a point where the
opening is slightly larger than the bit size you intend
to use.
3. Insert drill bit into the chuck the full length of the jaws.
WARNING
Do not insert drill bit into chuck jaws and tighten
as shown in Figure 19. This could cause drill bit to
be thrown from the drill press, resulting in possible
serious personal injury or damage to the chuck.
4. Tighten chuck jaws securely using chuck key
provided. Do not use a wrench to tighten or loosen
chuck jaws.
5. Remove chuck key.
6. To remove the drill bit, reverse the steps listed above.
WARNING
To avoid injury or accident by the chuck key ejecting
forcibly from the chuck when the power is turned
“ON”, use only the self-ejecting chuck key supplied
with this drill press. Always recheck and remove the
chuck key before turning the power “ON”. Place the
chuck key into its storage holder when not in use.
DRILLING TO A SPECIFIC DEPTH
Drilling a blind hole (not all the way through workpiece)
to a given depth can be done two ways:
Workpiece method
See Figure 27.
1. Mark the depth of the hole on the side of the
workpiece.
2. With the switch “OFF”, bring the drill bit down until
the tip is even with the mark.
3. Hold the feed handle at this position.
4. Spin the lower nut down to contact the depth stop
lug on the head.
5. Spin the upper nut down and tighten against the
lower nut.
6. The drill bit will now stop after traveling the distance
marked on the workpiece.
18
Original Instructions
Содержание RDP102L
