manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Time Processing Unit (eTPU)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

17-18

Freescale Semiconductor

4

MGEA

Microcode global exception engine A. Indicates that a global exception was asserted by microcode executed on 
the respective engine. The determination of the reason why the global exception was asserted is application 
dependent: it can be coded in an SDM status parameter, for instance. This bit is cleared by writing 1 to GEC.
0 No microcode-requested global exception pending.
1 Global exception requested by microcode is pending.

5

MGEB

Microcode global exception engine B. Indicates that a global exception was asserted by microcode executed on 
the respective engine. The determination of the reason why the global exception was asserted is application 
dependent: it can be coded in an SDM status parameter, for instance. This bit is cleared by writing 1 to GEC.
0 No microcode requested global exception pending.
1 Global exception requested by microcode is pending.

6

ILFA

Illegal instruction flag eTPU A. Set by the microengine to indicate that an illegal instruction was decoded in engine 
A. This bit is cleared by host writing 1 to GEC. For more information about illegal instructions, refer to Section 9.6 
in the 

eTPU Reference Manual

.

0 Illegal Instruction not detected.
1 Illegal Instruction detected by eTPU A.

7–10

Reserved.

11–15

SCMSIZE

[0:4]

SCM size. Holds the number of 2 KB SCM Blocks minus 1. This value is MCU-dependent.

16–20

Reserved.

21

SCMMISF

SCM MISC Flag. Set by the SCM MISC (multiple input signature calculator) logic to indicate that the calculated 
signature does not match the expected value, at the end of a MISC iteration. For more details, refer to the 

eTPU 

Reference Manual

 for more details.

0 Signature mismatch not detected.
1 MISC has read entire SCM array and the expected signature in ETPU_MISCCMPR does not match the value 

calculated.

This bit is cleared by writing 1 to GEC.

22

SCM

MISEN

SCM MISC enable. Used for enabling/disabling the operation of the MISC logic. SCMMISEN is readable and 
writable at any time. The MISC logic only operates when this bit is set to 1. When the bit is reset the MISC address 
counter is set to the initial SCM address. When enabled, the MISC continuously cycles through the SCM 
addresses, reading each and calculating a CRC. To save power, the MISC can be disabled by clearing the 
SCMMISEN bit. For more details, refer to the 

eTPU Reference Manual

.

0 MISC operation disabled. The MISC logic is reset to its initial state.
1 MISC operation enabled. (Toggling to 1 clears the SCMMISF bit)
SCMMISEN is cleared automatically when MISC logic detects an error; that is, when SCMMISF transitions from 
0 to 1, disabling the MISC operation.

23–24

Reserved.

25

VIS

SCM visibility. Determines SCM visibility to the slave bus interface and resets the MISC state (but SCMMISEN 
keeps its value).
0 SCM is not visible to the slave bus. Accessing SCM address space issues a bus error.
1 SCM is visible to the slave bus. The MISC state is reset. 
This bit is write protected when any of the engines are not in halt or stop states. When VIS=1, the ETPU_ECR 
MDIS bits are write protected, and only 32-bit aligned SCM writes are supported. The value written to SCM is 
unpredictable if other transfer sizes are used.

Table 17-6. ETPU_MCR Field Descriptions (continued)

Field

Description

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

S&C 6800 Series Instruction Sheet preview
6800 Series
Бренд: S&C Страницы: 40
L. G. B. 51099 Instructions preview
51099
Бренд: L. G. B. Страницы: 2
L-Acoustics LA4X Product Information preview
LA4X
Бренд: L-Acoustics Страницы: 36
UniPi Technology Patron S107 Quick Start Manual preview
Patron S107
Бренд: UniPi Technology Страницы: 4
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
Cooper S225-50-45 Service Information preview
S225-50-45
Бренд: Cooper Страницы: 4
Kele UCM-420A Operating And Installation Instructions preview
UCM-420A
Бренд: Kele Страницы: 33
mikroElektronika BIGdsPIC6 User Manual preview
BIGdsPIC6
Бренд: mikroElektronika Страницы: 28
Eaton ELC-PC12NNDR Instruction Sheet preview
ELC-PC12NNDR
Бренд: Eaton Страницы: 3
iXBlue MBC-AN-LAB Operating Manual preview
MBC-AN-LAB
Бренд: iXBlue Страницы: 20
TA DA 516 Manual preview
DA 516
Бренд: TA Страницы: 8
ZIEHL-ABEGG Acontrol PSET6 Operating Instructions Manual preview
Acontrol PSET6
Бренд: ZIEHL-ABEGG Страницы: 24
Control 4 HC-1000 V2 Installation Manual preview
HC-1000 V2
Бренд: Control 4 Страницы: 2
Pride Mobility LiNX Controller Basic Operation Instructions preview
LiNX Controller
Бренд: Pride Mobility Страницы: 16
Knoll VC100SS Installation Manual preview
VC100SS
Бренд: Knoll Страницы: 1
VelLight LEDC24 User Manual preview
LEDC24
Бренд: VelLight Страницы: 48
Carrera WIRELESS PLUS 20010111 Instructions Manual preview
WIRELESS PLUS 20010111
Бренд: Carrera Страницы: 24
Easyrain Rain Bird ESP-TM Series Installation, Programming, & Operation preview
Rain Bird ESP-TM Series
Бренд: Easyrain Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды