Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 1013 | Manualshive

Страница: 1013 / 1153

background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

24-20

Freescale Semiconductor

shows the various message formats that the pin interface formatter has to encounter.

The double edges in

indicate the starts and ends of messages. Fields without shaded areas

between them are grouped into super-fields and can be transmitted together without end-of-packet
indications between them.

24.7.2.2.1

Rules of Messages

The rules of messages include the following:

•

A variable-sized field within a message must end on a port boundary. (Port boundaries depend on
the number of MDO pins active with the current reset configuration.)

•

A variable-sized field may start within a port boundary only when following a fixed-length field.

•

Super-fields must end on a port boundary.

•

When a variable-length field is sized such that it does not end on a port boundary, it is necessary
to extend and zero fill the remaining bits after the highest order bit so that it can end on a port
boundary.

•

Multiple fixed-length packets may start and/or end on a single clock.

•

When any packet follows a variable-length packet, it must start on a port boundary.

•

The field containing the TCODE number is always transferred out first, followed by subsequent
fields of information.

•

Within a field, the lowest significant bits are shifted out first.

shows the transmission

sequence of a message that is made up of a TCODE followed by three fields.

Figure 24-7. Transmission Sequence of Messages

Figure 24-6. Message Field Sizes

Message

TCODE

Field #1

Field #2

Field #3

Field #4

Field #5

Min.

Size

1

Bits

1

Minimum information size. The actual number of bits transmitted depends on the number of MDO pins

Max.

Size

2

Bits

2

Maximum information size. The actual number of bits transmitted depends on the number of MDO pins

Device ID Message

1

Fixed = 32

N/A

N/A

N/A

N/A

38

38

FIELD #3

MSB

LSB

1

2

3

FIELD #2

FIELD #1

TCODE

4

6 bits

«
...
1011
1012
1013
1014
1015
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: ABB Страницы: 50

Бренд: FAAC Страницы: 44

Бренд: +GF+ Страницы: 3

Бренд: Ascon tecnologic Страницы: 16

Бренд: KIOUR Страницы: 3

Бренд: J+J Страницы: 6

Бренд: Progres Страницы: 2

Бренд: SMC Networks Страницы: 2

MediaDirector 2252B

Бренд: Harmonic Страницы: 2

Бренд: Drawmer Страницы: 16

Trovan Access Guard

Бренд: Dorset Страницы: 15

Бренд: Entryphone Страницы: 21

Princeton Applied Research PARSTAT 2273

Бренд: Ametek Страницы: 26

Бренд: Vello Страницы: 8

Бренд: Sices Страницы: 19

GUARDIAN CP DC2

Бренд: Amtrol Страницы: 12

Бренд: Pego Страницы: 32

Бренд: 3Ware Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды