Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 581 | Manualshive

Страница: 581 / 1153

background image

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

16-4

Freescale Semiconductor

16.1.3

eMIOS

Operating Modes

The eMIOS has the following operating modes:

16.1.3.1

Unified Channel Modes

The unified channels can be configured to operate in the following modes:

•

General purpose input/output

•

Single action input capture

•

Single action output compare

•

Input pulse-width measurement

•

Input period measurement

•

Double action output compare

•

Pulse/edge accumulation

•

Pulse/edge counting

•

Quadrature decode

•

Windowed programmable time accumulation

•

Modulus counter, normal

•

Modulus counter, buffered

•

Output pulse-width and frequency modulation, normal

•

Output pulse-width and frequency modulation, buffered

•

Center-aligned output pulse-width modulation with dead time insertion, normal

•

Center-aligned output pulse-width modulation with dead time insertion, buffered

•

Output pulse-width modulation, normal

•

Output pulse-width modulation, buffered

These modes are described in

Section 16.4.4.4, “Unified Channels Operating Modes

Table 16-1. eMIOS Operating Modes

Mode

Description

User

User mode is the normal operating mode. When EMIOS_MCR[FRZ] = 0, and EMIOS_CCR[FREN] = 0,
the eMIOS is in user mode.

Debug

Debug mode is individually programmed for each channel. When entering this mode, the UC registers’
contents are frozen, but remain available for read and write access through the slave interface. After
leaving debug mode, all counters that were frozen upon debug mode entry resume at the point where
they were frozen.
In debug mode, all clocks are running and all registers are accessible; thus, this mode is not intended for
power saving, but for use during software debugging.

Freeze

Freeze mode enables the eMIOS to freeze the registers of the unified channels when debug mode is
requested at the MCU level. While in freeze mode, the eMIOS continues to operate to allow the MCU
access to the unified channels’ registers. The unified channel remains frozen until the EMIOS_MCR[FRZ]
bit is cleared to zero, the MCU exits debug mode, or a unified channel’s EMIOS_CCR[FREN] bit is
cleared.

«
...
579
580
581
582
583
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Value Point Страницы: 7

Бренд: LANGER EMV-Technik Страницы: 48

Бренд: Yamaha Страницы: 5

Бренд: Ultraflex Страницы: 7

Бренд: Festo Страницы: 109

Бренд: Topworx Страницы: 8

Бренд: Samson Страницы: 44

Бренд: Hansen Страницы: 12

AquaLink RS All Button

Бренд: Jandy Страницы: 2

BoxControl Compact

Бренд: elero Страницы: 8

Бренд: Vent-Axia Страницы: 4

Бренд: Berkeley Страницы: 8

Бренд: mikroElektronika Страницы: 28

Бренд: Infineon Technologies Страницы: 2150

Бренд: Vector Страницы: 649

Бренд: C.A.P. Страницы: 2

DIGITAL TIMER CONTROL

Бренд: Truma Страницы: 66

Бренд: Atmel Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды