Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 513 | Manualshive

Страница: 513 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

12-68

Freescale Semiconductor

12.6

Document Revision History

Table 22. Changes Between MPC5565RM Revisions 0.1 and 1

Added: During a calibration bus access, the non-calibration bus signals (other than DATA) are held in a negated state, with
the exception of RD_WR and ADDR, which reflect the same values shown on the calibration version of those signals. This is
harmless because TS and CS are held negated on the non-calibration bus during calibration accesses, so no transfer takes
place on the non-calibration bus. DATA is not driven by the EBI during calibration accesses.
During a non-calibration bus access, the calibration bus signals (other than CAL_DATA) are held in a negated state. CAL_DATA
is not driven during non-calibration accesses.

Added corrected “Read After Write to the Same CS Bank” figure, and added the note: “In some cases, CS remains asserted
during this dead cycle, such as the cases of back-to-back writes or read-after-write to the same chip-select. See Figure 12-20
and Figure 12-21

.

In Table 12.4.2.3 changed:
• From: “To facilitate asynchronous write support, the EBI keeps driving valid write data on the data bus until 1 clock after the

rising edge where RD_WR and WE are negated (for chip select accesses only).”

• To: “To facilitate asynchronous write support, the EBI keeps driving valid write data on the data bus until 1 clock after the

rising edge where RD_WR (and WE for chip select accesses) are negated.

Figure 12-2 added the Calibration signals.

Section 12.4.1.9, “Port Size Configuration per Calibration Chip Select (16 Bits): Conditionalized for 496 assembly only.

Section 12.2.1.13, “Transfer Size 0 through 1 (TSIZ[0:1]): Added: Because the MPC5565 does not have transfer size pins
(TSIZ[0:1]), the SIZEN and SIZE fields of the EBI_MCR must be used for MCU-to-MCU transfers to indicate transfer size.

Section 12.3.1.3, “EBI Module Configuration Register (EBI_MCR) Added: Because the MPC5565 does not have transfer size
pins (TSIZ[0:1]), the SIZEN and SIZE fields of the EBI_MCR must be used for MCU-to-MCU transfers to indicate transfer size.

«
...
511
512
513
514
515
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Samsung Страницы: 32

Бренд: Galcon Страницы: 35

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 34

Бренд: S&C Страницы: 32

IntelliCap Plus

Бренд: S&C Страницы: 32

Бренд: S&P Страницы: 12

Бренд: S&C Страницы: 35

Бренд: MacroAir Technologies Страницы: 32

GAT Access 6600 Series

Бренд: Gantner Страницы: 4

Latherm HZR Comfort

Бренд: LAMBERTI ELEKTRONIK Страницы: 16

Touch Screen Controller SX112

Бренд: 3M Страницы: 33

Бренд: RADIKAL TECHNOLOGIES Страницы: 36

WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER

Бренд: Evoqua Страницы: 4

SoundLinQ SL2xD2

Бренд: Vais Technology Страницы: 21

ENFORCER SLI PR-B1124-PQ

Бренд: SECO-LARM Страницы: 2

Бренд: ULTRAFRYER Страницы: 1

Hauser COMPAX-M Series

Бренд: Parker Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды