manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

12-6

Freescale Semiconductor

NOTE

The internal bus grant input of the EBI is tied to a negated state. 

Because the MPC5565 does not have transfer size pins (TSIZ[0:1]), the SIZEN and SIZE fields in the 
EBI_MCR must be used for MCU-to-MCU transfers to indicate transfer size.

Refer to 

Section 12.5.5, “Dual-MCU Operation with Reduced Pinout MCUs

.” 

External master mode operation is described in 

Section 12.4.2.10, “Bus Operation in External Master 

Mode

.”

12.1.4.3

Module Disable Mode

The module disable mode is used for MCU power management. The clock to the non-memory mapped 
logic in the EBI is stopped while in module disable mode. Requests (other than to memory-mapped logic) 
must not be made to the EBI while it is in module disable mode, even if the clocks have not yet been shut 
off. In this case, the behavior is undefined. Module disable mode is entered when MDIS = 1 in the 
EBI_MCR.

12.1.4.4

Configurable Bus Speed Modes

In configurable bus speed modes, the external CLKOUT frequency is reduced to 1/2 or 1/4 compared to 
the internal system clock frequency. The EBI continues to operate according to the EBI mode selected, 
except that the EBI drives and samples signals at the scaled CLKOUT frequency rate rather than the 
internal system clock. This mode is selected by writing the external clock control register in the system 
integration module (SIU_ECCR). The configurable bus speed modes supports both 1/2 or 1/4 speed 
modes, meaning that the external CLKOUT frequency is scaled (divided) by 2 or 4 compared with that of 
the internal system clock, which remains unchanged.

12.1.4.5

16-Bit Data Bus Mode 

The EBI has an internal 32-bit data bus, but, for MCUs that have only 16 data bus signals pinned out, or 
for systems that use multiplexed signals (e.g. GPIO) on 16 of the 32 data pins, the EBI supports a 16-bit 
data bus mode. In this mode, DATA[0:15] are the only data signals used by the EBI. To enter 16-bit data 
bus mode, set the data bus mode field [DBM] in the EBI master control register (EBI_MCR[DBM]) to 
one. The reset value of DBM is 0. 

For EBI-mastered accesses, the operation in 16-bit data bus mode (EBI_MCR[DBM] = 1, 
EBI_BR

n

[PS] = x) is similar to a chip select access to a 16-bit port in 32-bit data bus mode 

(EBI_MCR[DBM] = 0, EBI_BR

n

[PS] = 1), except for the case of an EBI-mastered non-chip select access 

of exactly 32-bit size.

External master accesses and EBI-mastered non-chip select accesses of exactly 32-bit size are supported 
using a two beat 16-bit burst for both reads and writes. Except for chip-select (CS[

n

]) data transmissions, 

all data transmissions that are not 32 bits are supported in standard non-burst fashion.

Refer to 

Section 12.4.2.11, “Non-Chip-Select Burst in 16-bit Data Bus Mode

.” 

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Paoli F1 Operating And Maintenance Manual preview
F1
Бренд: Paoli Страницы: 16
Hach sc200 Software Update preview
sc200
Бренд: Hach Страницы: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Бренд: Hach Страницы: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Бренд: Hach Страницы: 472
Hach sc1000 User Manual preview
sc1000
Бренд: Hach Страницы: 64
Hach SC4500 Basic User Manual preview
SC4500
Бренд: Hach Страницы: 210
Davey Torrium 2 TT45 Installation And Operating Instructions Manual preview
Torrium 2 TT45
Бренд: Davey Страницы: 12
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Бренд: NEC Страницы: 30
SOMFY Situo 1 RTS Quick Installation Manual preview
Situo 1 RTS
Бренд: SOMFY Страницы: 56
Texas Instruments MSP430F67661 Manual preview
MSP430F67661
Бренд: Texas Instruments Страницы: 27
Allen-Bradley 1756-L72EROM Installation Instructions Manual preview
1756-L72EROM
Бренд: Allen-Bradley Страницы: 16
Sunricher SR-ZG9001T-RGBW Manual preview
SR-ZG9001T-RGBW
Бренд: Sunricher Страницы: 3
Watts WFHC 06Z 02 HC RF 24 User Manual preview
WFHC 06Z 02 HC RF 24
Бренд: Watts Страницы: 18
Texas Instruments Errata MSP430F6779 Manual preview
Errata MSP430F6779
Бренд: Texas Instruments Страницы: 27
Ubiquiti UA-Hub Quick Start Manual preview
UA-Hub
Бренд: Ubiquiti Страницы: 16
Mita WP3000 Manual preview
WP3000
Бренд: Mita Страницы: 7
LS Industrial Systems GLOFA G7M-DR20U User Manual preview
GLOFA G7M-DR20U
Бренд: LS Industrial Systems Страницы: 367
Danfoss PVE Series Installation Manual preview
PVE Series
Бренд: Danfoss Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды