Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 507 | Manualshive

Страница: 507 / 1153

background image

External Bus Interface (EBI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

12-62

Freescale Semiconductor

12.5.3

Running with Asynchronous Memories

The EBI also supports asychronous memories. In this case, the CLKOUT, TS, and BDIP pins are not used
by the memory and bursting is not supported. However, the EBI still drives these outputs, and always
drives and latches all signals at positive edge CLKOUT (i.e., there is no asynchronous mode for the EBI).
The data timing is controlled by setting the SCY bits in the appropriate option register to the proper number
of wait states to work with the access time of the asynchronous memory, just as done for a synchronous
memory.

12.5.3.1

Example Wait State Calculation

This example applies to any chip select memory, synchronous or asynchronous.

As an example, say we have a memory with 50 ns access time, and we are running the external bus at
66 MHz (CLKOUT period: 15.2 ns). When the input data specification for the MCU is 4 ns:

Number of wait states = (access time) / (CLKOUT period) + (0 or 1) (depending on setup time)

50/15.2 = 3 with 4.4 ns remaining (so we need at least three wait states, now check setup time)

15.2 - 4.4 = 10.8 ns (this is the achieved input data setup time)

Because actual input setup (10.8 ns) is greater than the input setup specification (4.0 ns), three wait states
is sufficient. If the input setup is less than 4.0 ns, use four wait states.

12.5.3.2

Timing and Connections for Asynchronous Memories

The connections to an asynchronous memory are the same as for a synchronous memory, except that the
CLKOUT, TS, and BDIP signals are not used.

shows a block diagram of an MCU connected

to an asynchronous memory.

«
...
505
506
507
508
509
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: RadioMaster Страницы: 49

Бренд: Cadac Страницы: 4

Бренд: Zamel Страницы: 2

Dual Motor Focus Controller

Бренд: Pegasus Astro Страницы: 16

Бренд: Grundfos Страницы: 80

Бренд: Maintronic Страницы: 53

Бренд: Pixsys Страницы: 24

CY3280-20x66 Universal CapSense

Бренд: Cypress Страницы: 2

Бренд: Pulsafeeder Страницы: 24

Бренд: IEI Technology Страницы: 81

SN32F260 Series

Бренд: SONIX Страницы: 141

Бренд: Watt Stopper Страницы: 3

Бренд: Niko Страницы: 4

MontBlanc KOSMOS CRUX-D

Бренд: Kohzu Precision Страницы: 74

MAXinBOX FANCOIL 2CH2P

Бренд: Zennio Страницы: 2

Бренд: Keithley Страницы: 97

Бренд: YASKAWA Страницы: 26

IP Power 9258AU

Бренд: Aviosys Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды