Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 1153

background image

e200z6 Core Complex

MPC5565 Microcontroller Reference Manual, Rev. 1.0

3-10

Freescale Semiconductor

— Interrupt vector prefix register (IVPR) and the interrupt vector offset registers

(IVOR1–IVOR15). These registers together provide the address of the interrupt handler for
different classes of interrupts.

— Save/restore registers (SRR0, SRR1). SRR0 holds the effective address for the instruction at

which execution resumes when an

rfi

instruction is executed at the end of a non-critical class

interrupt handler routine. SRR1 is used to save machine state on a non-critical interrupt, and
stores the MSR register contents. The MSR value is restored when an

rfi

instruction is executed

at the end of a non-critical class interrupt handler routine.

— Critical save/restore registers (CSRR0, CSRR1). CSRR0 holds the effective address for the

instruction at which execution resumes when an

rfci

instruction is executed at the end of a

critical class interrupt handler routine. CSRR1 is used to save machine state on a critical
interrupt, and stores the MSR register contents. The MSR value is restored when an

rfci

instruction is executed at the end of a critical class interrupt routine.

•

Debug facility registers

— Debug control registers (DBCR0–DBCR2). These registers provide control for enabling and

configuring debug events.

— Debug status register (DBSR). This register contains debug event status.

— Instruction address compare registers (IAC1–IAC4). These registers contain addresses and/or

masks which are used to specify instruction address compare debug events.

— Data address compare registers (DAC1, DAC2). These registers contain addresses and/or

masks which are used to specify data address compare debug events.

— e200z6 does not implement the data value compare registers (DVC1, DVC2).

•

Timer registers

— The clock inputs for the timers are connected to the internal system clock.

— Time base (TB). The TB is a 64-bit structure provided for maintaining the time of day and

operating interval timers. The TB consists of two 32-bit registers, time-base upper (TBU) and
time-base lower (TBL). The time-base registers can be written to by supervisor-level software
only, but can be read by both user and supervisor-level software.

— Decrementer register (DEC). This register is a 32-bit decrementing counter that provides a

mechanism for causing a decrementer exception after a programmable delay.

— Decrementer auto-reload (DECAR). This register is provided to support the auto-reload feature

of the decrementer.

— Timer control register (TCR). This register controls decrementer, fixed-interval timer, and

watchdog timer options.

— Timer status register (TSR). This register contains status on timer events and the most recent

watchdog timer-initiated processor reset.

For more details about these registers, refer to the Power Architecture embedded category specifications.

«
...
115
116
117
118
119
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: Panasonic Страницы: 31

Бренд: Panasonic Страницы: 31

Бренд: NAiS Страницы: 199

Бренд: Panasonic Страницы: 38

Бренд: Panasonic Страницы: 36

Бренд: Panasonic Страницы: 179

Бренд: Panasonic Страницы: 23

Бренд: BEIER-Electronic Страницы: 22

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: Balboa Страницы: 2

Бренд: Festo Страницы: 109

Бренд: Topworx Страницы: 8

Бренд: ISVT Страницы: 78

Бренд: Linear Technology Страницы: 8

Бренд: YASKAWA Страницы: 360

Бренд: TECH Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды