manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Flash Memory

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

13-23

 

13.4.1.7

FBIU Line Read Buffers and Prefetch Operation

The Flash BIU contains a pair of 256-bit line read buffers which are used to hold data read from the flash 
array. Each buffer operates independently and is filled using a single array access. The buffers are used for 
both prefetch and normal demand fetches. 

Prefetch triggering is controllable on a per-master and access-type basis. Bus masters can be enabled or 
disabled from triggering prefetches, and triggering can be further restricted based on whether a read access 
is for instruction or data and whether or not it is a burst access. A read access to the Flash BIU can trigger 
a prefetch to the next sequential line of array data on the cycle following the request. The access address 
is incremented to the next-higher 32-byte boundary, and a flash array prefetch is initiated if the data is not 
already resident in a line read buffer. Prefetched data is loaded into the buffer which is not being used to 
satisfy the original request.

Buffers can be in one of six states, listed here in prioritized order:

•

Invalid—the buffer contains no valid data.

•

Used—the buffer contains valid data which has been provided to satisfy a burst type read.

•

Valid—the buffer contains valid data which has been provided to satisfy a single type read.

•

Prefetched—the buffer contains valid data which has been prefetched to satisfy a potential future 
access.

•

Busy—the buffer is currently being used to satisfy a burst read.

•

Busy fill—the buffer has been allocated to receive data from the flash array, and the array access 
is still in progress.

Selection of a buffer to fill on a buffer miss is based on this prioritized order beginning with the first item 
(invalid). Selection of a buffer to fill on a triggered prefetch is based on the buffer which is not being used 
to satisfy the triggering access. 

The consequences of this replacement policy are that buffers are selected for filling on a ‘least recently 
updated’ basis when prefetching, and on a ‘most recently emptied’ basis for demand fetches (that is, a fetch 
which is actually satisfying a current system bus access). This policy allows for prefetched data to remain 
valid when non-prefetch enabled bus masters are granted flash access.

Several algorithms are available for prefetch control which trade off performance for power. They are 
described in 

Section 13.3.2.8, “Flash Bus Interface Unit Control Register (FLASH_BIUCR)

.” More 

aggressive prefetching increases power due to the number of wasted (discarded) prefetches, but can 
increase performance by lowering average read latency.

13.4.1.8

FBIU Instruction/Data Prefetch Triggering

Prefetch triggering can be enabled for instruction reads. Triggering can be enabled for all instruction reads 
or only for instruction burst reads. Prefetch triggering can be enabled for data reads. Triggering can be 
enabled for all data reads or only for data burst reads. Prefetches are not triggered by write cycles.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Watts KONTACT Manual preview
KONTACT
Бренд: Watts Страницы: 17
Purmo NC 24 V Assembly Instructions preview
NC 24 V
Бренд: Purmo Страницы: 2
salmson ACSON VARIO Installation And Starting Instructions preview
ACSON VARIO
Бренд: salmson Страницы: 78
D+H DXD 150-BSY+ Original Instructions Manual preview
DXD 150-BSY+
Бренд: D+H Страницы: 16
AMALGAMATED INSTRUMENT PM4-RT8 Operation And Instruction Manual preview
PM4-RT8
Бренд: AMALGAMATED INSTRUMENT Страницы: 27
ECO POWER CTR031 Installation Instructions preview
CTR031
Бренд: ECO POWER Страницы: 2
ACL CSC400 Installation And Operation Manual preview
CSC400
Бренд: ACL Страницы: 64
WOBIT SIC184 Manual preview
SIC184
Бренд: WOBIT Страницы: 25
Alpha C016-1540-10 Technical Manual preview
C016-1540-10
Бренд: Alpha Страницы: 16
Quantum Research Group QMatrix QT60486 User Manual preview
QMatrix QT60486
Бренд: Quantum Research Group Страницы: 11
Vestax PMC-06Pro T User Manual preview
PMC-06Pro T
Бренд: Vestax Страницы: 4
TDSi EXcel4 User Manual preview
EXcel4
Бренд: TDSi Страницы: 57
Nice PLUTO PL 4000 Instruction Manual And Spare Parts Catalogue preview
PLUTO PL 4000
Бренд: Nice Страницы: 16
FAAC 424 D LS Instructions For Use Manual preview
424 D LS
Бренд: FAAC Страницы: 14
OrangeRx MAT NX3 EVO Manual preview
MAT NX3 EVO
Бренд: OrangeRx Страницы: 2
OrangeRx RX3S Manual preview
RX3S
Бренд: OrangeRx Страницы: 4
Fastwel VIM301 User Manual preview
VIM301
Бренд: Fastwel Страницы: 54
Watts Vision BT-CT03 RF Quick Installation Manual preview
Vision BT-CT03 RF
Бренд: Watts Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды