Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 863 | Manualshive

Страница: 863 / 1153

background image

Deserial Serial Peripheral Interface (DSPI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

19-40

Freescale Semiconductor

19.4.4.1

DSI Master Mode

In DSI master mode the DSPI initiates and controls the DSI transfers. The DSI master has four different
conditions that can initiate a transfer:

•

Continuous

•

Change in data

•

Trigger signal

•

Trigger signal combined with a change in data

The four transfer initiation conditions are described in

Section 19.4.4.5, “DSI Transfer Initiation Control

Transfer attributes are set during initialization. The DSICTAS field in the DSPI

x

_DSICR determines

which of the DSPI

x

_CTARs controls the transfer attributes.

19.4.4.2

DSI Slave Mode

In DSI slave mode the DSPI responds to transfers initiated by an SPI or DSI bus master. In this mode the
DSPI does not initiate DSI transfers. Certain transfer attributes such as clock polarity and phase must be
set for successful communication with a DSI master. The DSI slave mode transfer attributes are set in the
DSPI

x

_CTAR1.

If the CID bit in the DSPI

x

_DSICR is set and the data in the DSPI

x

_COMPR differs from the selected

source of the serialized data, the slave DSPI asserts the MTRIG signal. If the slave’s internal hardware
trigger signal is asserted and the TRRE is set, the slave DSPI asserts MTRIG. These features are included
to support chaining of several DSPI. Details about the MTRIG signal are found in

Section 19.4.4.7,

“Multiple Transfer Operation (MTO)

.”

19.4.4.3

DSI Serialization

In the DSI configuration, 4 to 16 bits can be serialized using two different sources. The TXSS bit in the
DSPI

x

_DSICR selects between the DSPI

x

_SDR and DSPI

x

_ASDR as the source of serialized data. Refer

Section 19.3.2.11, “DSPI DSI Serialization Data Register (DSPIx_SDR)

Section 19.3.2.12,

“DSPI DSI Alternate Serialization Data Register (DSPIx_ASDR)

,” for more details. The DSPI

x

_SDR

holds the latest parallel input signal values which is sampled at every rising edge of the system clock. The
DSPI

x

_ASDR is written by host software and used as an alternate source of serialized data.

A copy of the last DSI frame shifted out of the shift register is stored in the DSPI

x

_COMPR. This register

provides added visibility for debugging and it serves as a reference for transfer initiation control.

Section 19.3.2.13, “DSPI DSI Transmit Comparison Register (DSPIx_COMPR)

,” contains details on the

DSPI

x

_COMPR.

«
...
861
862
863
864
865
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: NEC Страницы: 304

Бренд: IAI Страницы: 5

Бренд: Maestra Страницы: 22

Бренд: Ultratec Страницы: 33

Бренд: Rabbit Страницы: 12

Бренд: ccei Страницы: 16

Бренд: Espressif Systems Страницы: 11

CONPAL NCB-8C-SR

Бренд: Nabtesco Страницы: 24

MC-3000L-TC Series

Бренд: Lintec Страницы: 2

Бренд: CNC-Step Страницы: 127

Switch Pak A*13 series

Бренд: FlowLine Страницы: 6

Бренд: MDT Страницы: 39

LiNX Controller

Бренд: Pride Mobility Страницы: 16

DOMETIC SCC1012

Бренд: Zamp Solar Страницы: 8

Бренд: H-Tronic Страницы: 24

Бренд: SMSC Страницы: 65

Бренд: CoCo Страницы: 35

Бренд: Kohler Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды