manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Nexus

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

24-67

 

24.11.15.1 Single Write Access

1. Initialize the read/write access address register (RWA) through the access method outlined in 

Section 24.11.10, “ NZ6C3 Register Access via JTAG / OnCE

” using the Nexus register index 

of 0x9 (refer to 

Table 24-24

). Configure as follows:

– Write Address -> 0xnnnnnnnn (write address)

2. Initialize the read/write access control/status register (RWCS) through the access method outlined 

in 

Section 24.11.10, “ NZ6C3 Register Access via JTAG / OnCE

,” using the Nexus Register Index 

of 0x7 (refer to 

Table 24-24

). Configure the bits as follows:

– Access Control RWCS[AC] –> 0b1 (to indicate start access)

– Map Select RWCS[MAP] –> 0b000 (primary memory map)

– Access Priority RWCS[PR] –> 0b00 (lowest priority)

– Read/Write RWCS[RW] –> 0b1 (write access)

– Word Size RWCS[SZ] –> 0b0xx (32-bit, 16-bit, 8-bit)

– Access Count RWCS[CNT] –> 0x0000 or 0x0001 (single access)

NOTE

Access count RWCS[CNT] of 0x0000 or 0x0001 will perform a single 
access.

3. Initialize the read/write access data register (RWD) through the access method outlined in 

Section 24.11.10, “ NZ6C3 Register Access via JTAG / OnCE

,” using the Nexus register index of 

0xA (refer to 

Table 24-24

). Configure as follows:

– Write Data -> 0xnnnnnnnn (write data)

4. The NZ6C3 module will then arbitrate for the system bus and transfer the data value from the data 

buffer RWD register to the memory mapped address in the read/write access address register 
(RWA). When the access has completed without error (ERR=1’b0), NZ6C3 asserts the RDY

 

pin 

and clears the DV bit in the RWCS register. This indicates that the device is ready for the next 
access. 

NOTE

Only the RDY pin as well as the DV and ERR bits within the RWCS provide 
read/write access status to the external development tool.

24.11.15.2 Block Write Access (Non-Burst Mode)

1. For a non-burst block write access, follow Steps 1, 2, and 3 outlined in 

Section 24.11.15.1, “Single 

Write Access

 to initialize the registers,” but using a value greater than one (0x1) for the 

RWCS[CNT] field.

2. The NZ6C3 module will then arbitrate for the system bus and transfer the first data value from the 

RWD register to the memory mapped address in the read/write access address register (RWA). 
When the transfer has completed without error (ERR = 0), the address from the RWA register is 
incremented to the next word size (specified in the SZ field) and the number from the CNT field is 
decremented. Nexus will then assert the RDY pin. This indicates that the device is ready for the 
next access.

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

3Ware 9000 Series Specification preview
9000 Series
Бренд: 3Ware Страницы: 2
Oceanic ZX Service Procedure preview
ZX
Бренд: Oceanic Страницы: 13
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Бренд: u-blox Страницы: 2
Lab.gruppen LAB.LEVEL4 Quick Start Manual preview
LAB.LEVEL4
Бренд: Lab.gruppen Страницы: 2
Velleman KA01 Manual preview
KA01
Бренд: Velleman Страницы: 12
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Бренд: YASKAWA Страницы: 12
Grosvenor Janus C4 485 Installation Manual preview
Janus C4 485
Бренд: Grosvenor Страницы: 5
A10 Networks Harmony 2000 Quick Start Manual preview
Harmony 2000
Бренд: A10 Networks Страницы: 2
Giesecke & Devrient StarSign Bio Token 3.0 M Reference Manual preview
StarSign Bio Token 3.0 M
Бренд: Giesecke & Devrient Страницы: 28
GIESSE RACK MAX 650 Instruction And Installation Manual preview
RACK MAX 650
Бренд: GIESSE Страницы: 136
Advanced Control Technologies th104 Installation Instructions preview
th104
Бренд: Advanced Control Technologies Страницы: 3
Thermal Solutions Boiler Control TSBC Instruction Manual preview
Boiler Control TSBC
Бренд: Thermal Solutions Страницы: 48
RIFT Actuators RIFT 400 Installation, Operation & Maintenance Instructions Manual preview
RIFT 400
Бренд: RIFT Actuators Страницы: 23
Troy-Bilt TE31 Series User Manual preview
TE31 Series
Бренд: Troy-Bilt Страницы: 11
Integra 155000 Operating Instructions Manual preview
155000
Бренд: Integra Страницы: 17
Fisher 67D Series Instruction Manual preview
67D Series
Бренд: Fisher Страницы: 12
SANKI MFC-S3B Instruction Manual preview
MFC-S3B
Бренд: SANKI Страницы: 36
Bogobit Standard-Bremsmodul Manual preview
Standard-Bremsmodul
Бренд: Bogobit Страницы: 7

Бренды по названию

Популярные бренды

Загрузить еще бренды