manualshive.com logo in svg

Freescale Semiconductor MPC5565, Справочное руководство

Продукт Freescale Semiconductor MPC5565 - это мощный микроконтроллер с большой функциональностью и производительностью. Пользователи могут загрузить бесплатное Руководство по эксплуатации с manualshive.com, чтобы максимально эффективно использовать функционал устройства.

Поделиться
Скачать
background image

Enhanced Queued Analog-to-Digital Converter (eQADC)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

18-64

Freescale Semiconductor

•

Its commands are bound for an external command buffer that is not full, and it is the highest priority 
triggered CFIFO sending commands to an external buffer that is not full.

A triggered CFIFO with commands bound for a certain command buffer consecutively transfers its 
commands to the buffer until one of the following occurs:

•

An asserted end of queue bit is reached.

•

An asserted pause bit is encountered and the CFIFO is configured for edge trigger mode.

•

CFIFO is configured for level trigger mode and a closed gate is detected.

•

In case its commands are bound for an internal command buffer, a higher priority CFIFO that uses 
the same internal buffer is triggered.

•

In case its commands are bound for an external command buffer, a higher priority CFIFO that uses 
an external buffer is triggered.

The prioritization logic of the eQADC, depicted in 

Figure 18-37

, is composed of three independent 

submodules: one that prioritizes CFIFOs with commands bound for ADC0, another that prioritizes 
CFIFOs with commands for ADC1, and a last one that prioritizes CFIFOs with commands for external 
command buffer 2 and buffer 3. As these three submodules are independent, simultaneous commands to 
ADC0, to ADC1, and to eQADC SSI transmit buffer are allowed. The hardware identifies the destination 
of a command by decoding the EB and BN bits in the command message (see 

Section 18.4.1.2, “Message 

Format in eQADC

,” for details).

NOTE

Triggered but empty CFIFOs, underflowing CFIFOs, are not considered for 
prioritization. No data from these CFIFOs is sent to the on-chip ADCs or the 
external command buffers, and lower priority CFIFOs are not stopped from 
transferring commands.

Whenever ADC0 is able to receive new commands, the prioritization submodule selects the 
highest-priority triggered CFIFO with a command bound for ADC0, and sends it to the ADC. In case 
ADC0 is able to receive new entries but there are no triggered CFIFOs with commands bound for it, 
nothing is sent. The submodule prioritizing ADC1 usage behaves in the same way.

When the eQADC SSI is enabled and ready to start serial transmissions, the submodule prioritizing 
eQADC SSI usage writes command or null messages into the eQADC SSI transmit buffer, data written to 
the eQADC SSI transmit buffer is subsequently transmitted to the external device through the eQADC SSI 
link. The submodule writes commands to the eQADC SSI transmit buffer when there are triggered CFIFOs 
with commands bound for not-full external command buffers. The command written to the transmit buffer 
belongs to the highest priority CFIFO sending commands to an external buffer that is not full. This implies 
that a lower priority CFIFO can have its commands sent if a higher priority CFIFO cannot send its 
commands due to a full command buffer. The submodule writes null messages to the eQADC SSI transmit 
buffer when there are no triggered CFIFOs with commands bound for external command buffers, or when 
there are triggered CFIFOs with commands bound for external buffers but the external buffers are full. The 
eQADC monitors the status of the external buffers by decoding the BUSY fields of the incoming result 
messages from the external device (see 

Section , “Result Message Format for External Device Operation

,” 

for details). 

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

wattio AIR Read Me preview
AIR
Бренд: wattio Страницы: 20
Parasound 7100 Owner'S Manual preview
7100
Бренд: Parasound Страницы: 72
Particle B Series Quick Start Manual preview
B Series
Бренд: Particle Страницы: 6
KEB COMBIVERT F5 Safety Manual preview
COMBIVERT F5
Бренд: KEB Страницы: 16
IDTECK Star RFL200 Quick Manual preview
Star RFL200
Бренд: IDTECK Страницы: 12
Banner XS26-2 Series Manual preview
XS26-2 Series
Бренд: Banner Страницы: 2
Eaton CGLine+ Web Controller Installation And Operating Instructions Manual preview
CGLine+ Web Controller
Бренд: Eaton Страницы: 28
Eaton Cutler-Hammer Jockey Instructions Manual preview
Cutler-Hammer Jockey
Бренд: Eaton Страницы: 12
Watlow DIN-A-MITE C User Manual preview
DIN-A-MITE C
Бренд: Watlow Страницы: 20
Unimig UNI-FLAME REG Operation Manual preview
UNI-FLAME REG
Бренд: Unimig Страницы: 4
Samson 2371-10 Mounting And Operating Instructions preview
2371-10
Бренд: Samson Страницы: 36
NCE CAB-04p Operation Manual preview
CAB-04p
Бренд: NCE Страницы: 4
American Lighting TRULUX DMX 3Z Touch Control Installation Instructions Manual preview
TRULUX DMX 3Z Touch Control
Бренд: American Lighting Страницы: 2
HomeMatic HM-Sec-SFA-SM Installation And Operating Manual preview
HM-Sec-SFA-SM
Бренд: HomeMatic Страницы: 38
Arbor Technology ELIT-1270 User Manual preview
ELIT-1270
Бренд: Arbor Technology Страницы: 79
HobbyKing NanoWii Manual preview
NanoWii
Бренд: HobbyKing Страницы: 16
Cablematic 192DMX User Manual preview
192DMX
Бренд: Cablematic Страницы: 6
VRG Controls RCVC 3000 Instruction Manual preview
RCVC 3000
Бренд: VRG Controls Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды