Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 596

Страница: 596 / 1153

Enhanced Modular Input/Output Subsystem (eMIOS)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

Freescale Semiconductor

16-19

0001001

Pulse and edge accumulation (single shot)

0001010

Pulse and edge counting (continuous)

0001011

Pulse and edge counting (single shot)

0001100

Quadrature decode (for count and direction encoders type)

0001101

Quadrature decode (for phase_A and phase_B encoders type)

0001110

Windowed programmable time accumulation

0001111

Reserved

0010000

Modulus counter. Up counter, internal clock source.

0010001

Modulus counter. Up counter, external clock source.

0010010–0010011

Reserved

0010100

Modulus counter. Up/down counter, no change in counter direction upon match of input counter
and register B1, internal clock source.

0010101

Modulus counter. Up/down counter, no change in counter direction upon match of input counter
and register B1, external clock source.

0010110

Modulus counter. Up/down counter, change in counter direction upon match of input counter and
register B1 and sets the FLAG, internal clock source.

0010111

Modulus counter. Up/down counter, change in counter direction upon match of input counter and
register B1 and sets the FLAG, external clock source.

0011000

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator B, immediate update.

0011001

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator B, next period update.

0011010

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator A or comparator B, immediate update.

0011011

Output pulse-width and frequency modulation. FLAG set at match of internal counter and
comparator A or comparator B, next period update.

0011100

Center-aligned output pulse-width modulation. FLAG set in trailing edge, trailing edge dead-time.

0011101

Center-aligned output pulse-width modulation. FLAG set in trailing edge, leading edge dead-time.

0011110

Center-aligned output pulse-width modulation. FLAG set in both edges, trailing edge dead-time.

0011111

Center-aligned output pulse-width modulation. FLAG set in both edges, leading edge dead-time.

0100000

Output pulse-width modulation. FLAG set at match of internal counter and comparator B,
immediate update.

0100001

Output pulse-width modulation. FLAG set at match of internal counter and comparator B, next
period update.

0100010

Output pulse-width modulation. FLAG set at match of internal counter and comparator A or
comparator B, immediate update.

Table 16-10. Binary Values for Unified Channel Operating Modes (continued)

MODE[0:6]

Unified Channel Operating Modes

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды

Freescale Semiconductor MPC5565, Справочное руководство

Результаты поиска

Содержание MPC5565

Отзывы:

Похожие инструкции для MPC5565

Бренды по названию

Популярные бренды