Freescale Semiconductor MPC5565 Скачать руководство пользователя страница 919 | Manualshive

Страница: 919 / 1153

background image

Enhanced Serial Communication Interface (eSCI)

MPC5565 Microcontroller Reference Manual, Rev. 1.0

20-24

Freescale Semiconductor

NOTE

LIN 2.0 now requires that a break character is always 13 bits long, so the
BRK13 bit should always be set to 1. The eSCI works with BRK13=0, but
it violates LIN 2.0.

The eSCI recognizes a break character when a start bit is followed by eight or nine logic 0 data bits and a
logic 0 where the stop bit should be. Receiving a break character has the following effects on eSCI
registers:

•

Sets the framing error flag, FE.

•

Sets the receive data register full flag, RDRF.

•

Clears the eSCI data register (ESCI

x

_DR).

•

Can set a flag: overrun (OR), noise flag (NF), parity error flag (PF), or the receiver active flag
(RAF). For more details, Refer to

Section 20.3.3.4, “eSCI Status Register (ESCIx_SR)

20.4.4.4

Idle Characters

An idle character contains all logic 1s and has no start, stop, or parity bit. Idle character length depends on
the M bit in eSCI control register 1 (ESCI

x

_CR1). The preamble is a synchronizing idle character that

begins the first transmission initiated after toggling the TE bit from 0 to 1.

If the TE bit is cleared during a transmission, the TXD output

becomes idle after completion of the

transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle
character to be sent after the frame currently being transmitted.

NOTE

When queueing an idle character, return the TE bit to logic 1 before the stop
bit of the current frame shifts out through the TXD output. Setting the TE
bit after the stop bit shifts out through the TXD output

causes data

previously written to the eSCI data register to be lost. Toggle the TE bit for
a queued idle character while the TDRE flag is set and immediately before
writing the next byte to the eSCI data register.

«
...
917
918
919
920
921
...
»

Содержание MPC5565


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MPC5565

Бренд: UniKey Страницы: 20

Бренд: Eaton Страницы: 2

Бренд: National Instruments Страницы: 72

Бренд: Greenheck Страницы: 4

Бренд: YASKAWA Страницы: 360

Бренд: ADLINK Technology Страницы: 37

Бренд: V2 Страницы: 108

Бренд: Swagelok Страницы: 6

Бренд: NI Страницы: 135

Бренд: Danfoss Страницы: 22

SmartLoop KTSL-FC1-UV-KO

Бренд: Keystone Страницы: 2

ISaGRAF VP-23W7

Бренд: ICP DAS USA Страницы: 192

Бренд: ascon Страницы: 20

Бренд: gefran Страницы: 16

Бренд: ST Страницы: 25

5268 Servocontrol

Бренд: Viessmann Страницы: 4

Бренд: Abus Страницы: 39

Бренд: Regada Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды